Drip Line Length Calculator

Work out the longest a drip lateral (dripline or drip tape) can run before the emitters at the far end get too little pressure to water evenly. Enter your tubing, emitter flow and spacing, inlet pressure and slope. Non-PC rows are limited by flow variation; pressure-compensating rows by the emitters’ minimum pressure.

Drip line length calculator

Choose your emitter type
Quick picks

1Tubing and emitters

Sets the inside diameter. Check your product’s spec sheet.

in
in
GPH

From the spec sheet (the “x” in q = k × P^x).

2Pressure and slope

psi

Pressure where the lateral starts, while running. Spec sheet in metres of head? Divide by 10.2 for bar.

%

10 % is the common design target for uniform watering.

%

Uphill +, downhill −, e.g. −0.5 for a gentle fall.

ft per emitter

Advanced. Include if your manufacturer gives it; leave 0 for drip tape.

ft

Optional: shows how uneven an existing row is.

See the maximum run ↓

How the calculator works

This page answers “how long can one drip row be?” It is not about how much dripline to buy; for footage, use the drip irrigation calculator.

Water flows into the row at the inlet and leaves through every emitter, so the flow falls along the row. Friction uses up pressure on the way. The calculator lengthens the row foot by foot until the pressure lost reaches what your design allows.

  • Emitter lawq = k × P^x (x ≈ 0.5 for turbulent non-PC emitters, near 0 for PC)
  • Allowed loss, non-PCΔP = Pinlet × [1 − (1 − variation)^(1 ÷ x)]
  • Allowed loss, PCΔP = Pinlet − minimum regulating pressure
  • Frictionhf = f × (L ÷ D) × v² ÷ 2g, Blasius f = 0.3164 × Re^−0.25 (laminar 64 ÷ Re)
  • Many outletsloss = F × hf, F = 1 ÷ (m + 1) + 1 ÷ 2N + √(m − 1) ÷ 6N², m = 1.75
  • Slope0.433 psi per foot of rise (uphill +, downhill −)
  • Maximum lengththe longest row with friction × F + slope ≤ ΔP
  • Your rowvariation = 1 − (1 − loss ÷ Pinlet)^x

Worked examples

Drip tape on level ground

  1. Inputs5/8-in tape (0.625 in), 0.22 GPH every 12 in, 8 psi, 10 % variation, exponent 0.5.
  2. Allowed loss8 × [1 − 0.9²] = 1.52 psi.
  3. Result401 ft. Allowing 15 % variation raises the loss to 2.22 psi and the run to 460 ft.

The same tape on a slope

  1. Uphill 1 %Each 100 ft of rise costs 0.43 psi of the 1.52 psi allowance: 252 ft.
  2. Downhill 0.5 %The fall gains pressure and offsets friction: 485 ft.

Landscape and PC dripline

  1. Non-PC0.600-in dripline, 0.9 GPH every 12 in, 25 psi, 10 %: allowed loss 4.75 psi, 231 ft.
  2. PC0.55-in dripline, 0.4 GPH every 12 in, 30 psi inlet, 10 psi minimum: allowed loss 20 psi, 561 ft by the model. The manufacturer chart for a similar product lists 411 ft; follow the chart.
  3. Metric16 mm dripline (13.6 mm ID), 2 L/h every 30 cm, 1.0 bar, 10 %: 66 m.

Pressure-compensating vs non-PC run lengths

A non-PC emitter with exponent 0.5 changes flow about 10 % for a 20 % change in pressure. To keep variation within 10 %, the row can lose only about a fifth of its inlet pressure. A PC emitter holds its flow from its minimum pressure upward, so a 30 psi inlet with a 10 psi minimum can lose 20 psi. That is why PC dripline usually runs much farther.

Allowed pressure loss for 10 % flow variation (non-PC) by exponent.
Inlet pressurex = 0.4x = 0.5x = 0.6
8 psi1.85 psi1.52 psi1.29 psi
15 psi3.47 psi2.85 psi2.42 psi
25 psi5.79 psi4.75 psi4.03 psi

Find your emitter’s exponent on its spec sheet, or measure it with the emitter flow calculator.

Slope and drip runs

Uphill rows lose 0.433 psi for every foot they climb, on top of friction, so they shorten fast. Gentle downhill rows gain pressure, which offsets friction and lets them run longer. On a steep fall the far emitters can end up with more pressure than the inlet, which is also uneven; check the tubing’s maximum pressure rating. Lay rows across the slope or downhill where you can.

What flow variation means

Flow variation ratings.
VariationRatingWhat to do
10 % or lessDesirable: uniformKeep the layout.
10–20 %AcceptableFine for most landscapes; tighten for crops.
Over 20 %UnacceptableShorten rows, raise inlet pressure, use larger tubing or PC emitters.

Enter your current row length in the non-PC tab to see where your rows sit.

Tubing size and centre feeding

Friction falls steeply as tubing gets wider, so a larger inside diameter is the most effective way to lengthen runs. Closer emitter spacing or higher emitter flow does the opposite: more water in the tubing means more friction. Feeding a row from the middle, or from both ends, makes two laterals out of one and roughly doubles the length one inlet can cover.

Mistakes to avoid

Using static pressure

Enter the pressure at the inlet while the zone runs, after the regulator. Static pressure overstates the run.

Ignoring the chart

For inline dripline the manufacturer’s chart includes losses at each emitter. When one exists, it wins.

Outside diameter as ID

“1/2-in” dripline has an inside diameter of about 0.55–0.70 in. Use the ID from the spec sheet.

PC emitters below their minimum

Under the minimum regulating pressure a PC emitter behaves like a non-PC one. Keep the far end above it.

How we build and check this calculator

Every formula on this page names its source, and the code is tested against worked cases before every update.

  • Methods from recognised sources. The emitter law and the 10 % criterion follow ISO-based manufacturer data and the B.C. Trickle Irrigation Manual; the acceptability bands follow an Irrigation Association paper; the friction model is standard microirrigation hydraulics. See the sources.
  • Tested against worked cases. Nine cases run against the calculator code before every update: tape at 10 % and 15 %, landscape dripline, uphill and downhill rows, PC dripline, a metric row, the IA 2012 model check and an inlet below the PC minimum. All must match.
  • Honest about limits. The model is general. It can run longer than product charts for inline dripline, and very long laterals are also limited by flushing time.
  • Your entries stay on your device. The calculator runs in your browser. Nothing you type is sent anywhere; your inputs live only in the page address, so you can bookmark or share a result.
  • Corrections are welcome. If a number looks wrong, tell us. We check it against the sources, fix the page and update the date at the top.

Page history

Published. Methods, test cases and source links checked.

Questions

How long can a drip line be?

It depends on tubing size, emitter flow and spacing, pressure and slope. Low-flow drip tape at 8 psi can run about 400 ft on level ground; 1/2-in landscape dripline with 0.9 GPH emitters at 25 psi runs a little over 200 ft. The calculator works it out for your setup.

Why do emitters at the end of a long row get less water?

Water loses pressure to friction as it flows along the tubing, and the near end carries the flow for the whole row. Non-compensating emitters give less flow at lower pressure, so the far end gets less water.

Do pressure-compensating emitters allow longer runs?

Usually, yes. PC emitters keep the same flow until pressure falls to their minimum, so the whole drop from inlet pressure down to that minimum is usable. Non-PC rows can only lose a small part of their inlet pressure before flow varies too much.

How does slope change drip run length?

Each foot of rise costs 0.433 psi, so rows running uphill get much shorter; a 1 % slope cut a 401 ft tape row to 252 ft in our example. A gentle downhill run gains pressure and gets longer. Run rows across or down the slope where you can.

What does 10 % flow variation mean?

The emitter with the least water gets at least 90 % of what the emitter with the most gets. Manufacturers treat 10 % as uniform irrigation; 10–20 % is acceptable, and over 20 % is not.

Can I double the run by feeding from the middle?

Yes. Feeding a row from the centre makes two laterals, each up to the maximum length, so the row can be about twice as long overall. Feeding from both ends works the same way.

Why is the manufacturer’s chart shorter than this result?

Inline emitters disturb the flow inside the tubing, which adds loss this general model leaves out unless you enter an allowance. For example, a PC dripline chart lists 411 ft where the model gives 561 ft. Use the chart for that product; use this calculator where there is no chart or to compare options.

Sources

  1. Netafim, Streamline X technical product sheet. Dripper flow Q = K × P^x, flow variation FV = (Qmax − Qmin) ÷ Qmax × 100, 10 % as the uniform-irrigation criterion, and lateral length tables by slope.
  2. Irrigation Association (Lamm & Rogers, Kansas State University), Hydraulic Considerations for SDI Systems (2012 Technical Conference). Flow variation of 10 % or less desirable, 10–20 % acceptable, over 20 % unacceptable (Bralts et al., 1987), and the 0.785-in dripline example used as a model check.
  3. Hunter Industries, HDL-PC and HDL-R: Maximum Run Lengths. Manufacturer run-length tables for PC dripline by pressure, spacing and flow, with a 10 psi minimum operating pressure.
  4. B.C. Ministry of Agriculture and Food, B.C. Trickle Irrigation Manual (1999), Appendix E: Equations. Emitter flow rate and discharge exponent equations and allowable pressure variation.
  5. Oklahoma State University Extension, Drip Irrigation Systems (BAE-1511). Drip tape sizes and their use in row crops.
  6. The lateral model (Darcy-Weisbach with the Blasius friction factor, the Christiansen multiple-outlet factor with m = 1.75, 0.433 psi per foot of rise) is standard microirrigation hydraulics as set out in Keller and Bliesner’s Sprinkler and Trickle Irrigation; it uses no product data.

Links checked November 15, 2026. The model reproduces the IA 2012 example (0.785-in ID, 0.20 GPH every 12 in, 10 psi) at 4.1 % flow variation for 500 ft against the paper’s 4 %.