Sprinkler Calculators

Lay out heads, check how fast and how evenly a zone waters, size nozzles to your pressure, split heads into zones your supply can run, and pick the right valve wire. Six calculators for designing a sprinkler system or tuning one you already have.

Which calculator do you need?

All Sprinkler calculators

Designing a zone, step by step

A good sprinkler zone has heads that reach each other, nozzles matched to the pressure, and no more flow than the supply can give.

  1. Know your supplyFind the gallons per minute your water line can give with the available flow calculator.
  2. Space the headsPick a head, then lay it out head to head with the sprinkler spacing calculator.
  3. Check nozzle flowAdjust the chart flow to your real pressure with the nozzle flow calculator.
  4. Group heads into zonesFit the heads to your supply, one head type per zone, with the sprinkler zone calculator.
  5. Wire the valvesConfirm the wire gauge for the longest run with the irrigation wire size calculator.
  6. Check the rateFind the zone’s inches per hour with the precipitation rate calculator, then set run times.
  • Precipitation ratein/hr = 96.25 × total GPM ÷ area (sq ft)
  • Head spacinghead to head: spacing = throw radius; triangular rows = 0.866 × spacing
  • Nozzle at a new pressureQ₂ = Q₁ × √(P₂ ÷ P₁)
  • Scheduling multiplierSM = 1 ÷ (0.4 + 0.6 × DU)

Head types compared

Typical values at head-to-head spacing and normal pressure. Your nozzle chart gives exact figures.
HeadRate, in/hrTypical flowHeads per 8 GPM zone
Fixed spray1.0–2.01.5 GPM5
Rotary nozzle0.4–0.60.6 GPM13
Gear-driven rotor0.3–0.83.0 GPM2
Impact0.2–0.64.0 GPM2

The 8 GPM zone is 80 % of a 10 GPM supply, the margin the zone calculator uses by default.

Tuning a system you already have

Set out catch cups across a zone, run it, and enter the readings in the distribution uniformity calculator. It gives the DU, the zone’s real precipitation rate and the multiplier to use in the run time calculator.

Irrigation Association ratings for lower-quarter DU.
RatingSpray headsRotors and rotary nozzles
Excellent75 % and up80 % and up
Very good65–74 %70–79 %
Good55–64 %65–69 %
Repair before schedulingunder 40 %under 50 %

A poor DU is usually a fixable problem: tilted or sunken heads, blocked nozzles, mixed nozzle brands or low pressure. Check pressure loss with the irrigation pressure calculator before adding run time.

Mistakes to avoid

Stretching the spacing

Heads set beyond head to head leave dry rings between them that no run time can fix.

Too many heads on a valve

Over-filling a zone drops the pressure, so every head throws short.

Half-circle, full nozzle

Part-circle heads need matched nozzles so the corners don’t get double the water.

Ignoring the common wire

Several valves on one common wire add up the current. Size the wire for the worst case.

How we build and check these calculators

  • Methods from recognised sources. Irrigation Association technical papers and published manufacturer engineering data, named on every calculator page.
  • Tested before every update. Each calculator runs its worked cases in US and metric units before a change goes live.
  • Open about method and limits. Read our editorial policy, or tell us if a number looks wrong.

Questions

How far apart should sprinkler heads be?

Head to head, so the spray from each head reaches the next one. That means spacing equals the throw radius, or 50 % of the throw diameter. In windy spots, closer spacing keeps coverage even.

What is a good precipitation rate?

There is no single right rate, but it should suit the soil. Fixed sprays apply about 1 to 2 inches an hour, rotary nozzles about 0.4 to 0.6, and rotors about 0.3 to 0.8. Slow-soaking clay does better with low-rate heads or cycle and soak.

Can I mix spray heads and rotors on one zone?

It’s best not to. They put water down at very different rates, so one area floods while the other stays dry. Keep each zone to one head type with matched precipitation nozzles.

What is distribution uniformity?

A measure of how evenly a zone waters, from catch-cup readings. Lower-quarter DU compares the driest quarter of cups with the average; 75 % or more is excellent for spray heads.

How many sprinkler heads per zone?

As many as your supply can feed with some margin. On a 10 GPM supply, that is about five fixed sprays at 1.5 GPM or two rotors at 3 GPM. The zone calculator works it out from your flow and nozzle chart.

What wire size do I need for sprinkler valves?

18 AWG multi-strand irrigation cable works for most home runs up to about 800 ft with a typical solenoid. For longer runs, or several valves sharing one common, upsize the common first. The wire calculator checks the voltage that reaches the solenoid.

Sources

  1. Rain Bird Corporation, Irrigation Design Tip — Sprinkler Spacing Patterns. Head-to-head spacing and square and triangular patterns.
  2. Rain Bird Corporation, Precipitation rate equations (catalogue technical data). The 96.25 precipitation rate equation for square, triangle and zone-area layouts.
  3. Irrigation Association, Using Distribution Uniformity to Evaluate the Quality of a Sprinkler System. Lower-quarter DU, catch-cup tests and the scheduling multiplier.
  4. Hunter Industries, Residential System Design Guide (LIT-226). Zoning by head type and flow, and supply checks.
  5. Nelson Irrigation, Control Wire Size Notes (VM-20.11). Voltage drop in valve wire and minimum solenoid voltage.

Links checked November 16, 2026. Each calculator page lists its own full set of sources. Manufacturer documents are cited for their engineering data only; we have no ties to any manufacturer.