Farm Irrigation Calculators

Field-scale irrigation math with the working shown. Size a well or pump to peak crop use, set a center pivot timer, plan furrow sets, mix and inject fertilizer, read a weir or flume, and convert between acre-inches, cfs and gpm.

Which calculator do you need?

All Farm calculators

Planning the season

A field system has to keep up with the crop on its hottest days. Start with the crop’s peak use, size the supply to it, then manage each pass or set.

  1. Find peak crop useGet daily ET with the ET calculator and the crop’s need with the water requirement calculator.
  2. Size the flowTurn peak use into gpm per acre and total gpm, or acres per well, with the system capacity calculator.
  3. Measure what you haveRead a ditch delivery with the weir and flume flow calculator.
  4. Manage each applicationSet pivot passes with the center pivot calculator or furrow sets with the furrow irrigation calculator.
  5. Feed through the waterSet the injector with the fertigation calculator.
  6. Track the totalsConvert water rights, deliveries and pumping into the same unit with the acre-inch converter.
  • System capacitygpm per acre = peak use (in a day) × 452.57 ÷ (pumping hours × efficiency)
  • Pivot depthgross inches = gpm × hours per revolution × 60 ÷ (acres × 27,154)
  • Furrow depthgross inches = 1,155 × gpm per furrow × hours ÷ (length ft × wetted spacing in)
  • Fertigationinjection gpm = flow × 8.345 × ppm ÷ (1,000,000 × lb nutrient per gallon)

Rules of thumb

Exact values used by the calculators, with the field rounding.
RelationExactField rounding
1 acre-inch27,154.29 gal27,200 gal
1 cfs448.83 gpm450 gpm
1 cfs for 1 hour0.992 acre-in1 acre-in
1 cfs for 1 day1.98 acre-ft2 acre-ft
1 acre-inch an hour452.57 gpm450 gpm

Miner’s inches depend on the state: 40 per cfs in Arizona, California, Montana, Nevada and Oregon, 50 in Idaho, Kansas, Nebraska, New Mexico, North Dakota and Utah, and 38.4 in Colorado.

Pivot, furrow or drip

Typical application efficiency by system (NCAT ATTRA ranges used in the calculators).
SystemTypical efficiencyManaged with
Center pivot, impact sprinklers75–90 %Center pivot calculator
Solid set or hand move70–85 %System capacity calculator
Furrow60–80 %Furrow irrigation calculator
Drip85–95 %Drip calculators

Higher efficiency means less water pumped for the same crop use, and lower pumping cost; price it with the pumping cost calculator and size the pump with the irrigation pump calculator.

Mistakes to avoid

Forgetting downtime

24 hours of load control a week means 168 hours of work in 144. Capacity must rise by 1.167.

Machine length as the radius

Water reaches past the last tower, about 40 ft, or 75 ft with an end gun. That adds acres.

Trusting average depth

A furrow set can average the right depth while the top end is soaked. Check the cutoff ratio.

Chemigation without safety gear

Injection needs the backflow and interlock equipment your state and the label require.

How we build and check these calculators

  • Methods from recognised sources. University of Nebraska, UF/IFAS and K-State Extension, NCAT ATTRA and the U.S. Bureau of Reclamation, named on every calculator page.
  • Tested against published examples. Each calculator reproduces worked examples from its sources in US and metric units before a change goes live.
  • Open about method and limits. Read our editorial policy, or tell us if a number looks wrong.

Questions

How many gpm per acre do I need?

It depends on peak crop water use, pumping hours, efficiency and downtime. Many designers use about 6 to 7.5 gpm per acre for full irrigation in dry summers; sandy soils and hot regions need more.

How many gallons are in an acre-inch?

27,154 US gallons, which is an inch of water over one acre. One cfs running for an hour delivers about one acre-inch.

How do I set a pivot percent timer for 1 inch?

Find the depth at 100 % (full speed). Timer % = depth at 100 % ÷ target depth × 100. A pivot that puts on 0.28 in at full speed needs about 27.5 % for 1 inch.

What is a cutoff ratio in furrow irrigation?

The time water takes to reach the end of the furrow divided by the set time. University of Nebraska targets range from about 0.2 on sandy soil with tailwater reuse to 0.95 on clay with blocked ends.

Why does product density matter in fertigation?

ppm is by weight. A gallon of UAN-32 weighs about 11.05 lb and carries about 3.54 lb of nitrogen, so treating it as weighing the same as water overstates the injection rate.

Which weirs and flumes are covered?

Contracted and suppressed rectangular weirs, 90° V-notch and Cipolletti weirs, and Parshall flumes from 1 in to 50 ft, using U.S. Bureau of Reclamation equations.

Sources

  1. University of Nebraska–Lincoln Extension, Minimum Center Pivot Design Capacities in Nebraska (G1851). System capacity from peak water use, pumping hours, efficiency and downtime.
  2. University of Nebraska–Lincoln Extension, Managing Furrow Irrigation Systems (G1338). Furrow depth equation, cutoff ratio targets and stream size.
  3. University of Florida IFAS Extension, How to Calculate Fertigation Injection Rates for Commercial Blueberry Production (HS1197). Injection rate method and nitrogen concentration guidance.
  4. U.S. Bureau of Reclamation, Water Measurement Manual, Chapter 8 — Parshall Flumes. Flume rating equations and submergence limits.
  5. Oklahoma State University Extension, Water Measurement Units and Conversion Factors. Acre-inch, acre-foot, cfs and gpm relations.

Links checked November 16, 2026. Each calculator page lists its own full set of sources.