Fertigation Calculator

Set a fertilizer injector three ways. Hold a target ppm in the irrigation water, mix a stock tank for a proportional injector (1:16, 1:100, 1:200), or put on a set rate per acre during a pivot pass or drip set. Product strength is handled by weight, so the ppm is right for heavy liquids like UAN-32, and the result gives gph, gpm, ounces and millilitres per minute for checking the pump with a jar and stopwatch.

Fertigation calculator

Work it out from
Quick picks

1Product

lb/gal

UAN-32 is about 3.54 lb N per gallon; check your label.

% by weight
lb/gal

From the label or SDS; UAN-32 is about 11.05 lb/gal.

2Water and target

GPM
ppm (mg/L)
lb

Gives product volume and injection time.

3Optional checks

GPH
GPH
%
See the injection rate ↓

How the calculator works

The pump must add the right weight of nutrient to every gallon of irrigation water. That depends on the flow, the target and how much nutrient each gallon of product carries.

  • Product strengthlb nutrient per gallon = label value, or % × density, or % × 8.345
  • Target ppminjection gpm = flow × 8.345 × ppm ÷ (1,000,000 × strength); gph = × 60
  • Stock tankoz/gal = ppm × X ÷ (% × 74.89); lb/gal = ppm × X ÷ (% × 1,198.3); g/L = ppm × X ÷ (% × 10)
  • Rate per acreproduct = rate ÷ strength (or gal per acre) × acres; gph = product ÷ hours
  • Resulting ppmgph × strength ÷ (flow × 60 × 8.345) × 1,000,000
  • Line concentration% = gph × 100 ÷ (60 × flow)
  • Calibrationoz/min = gpm × 128; mL/min = gpm × 3,785

Worked examples

150 ppm N through drip

  1. Inputs1,000 gpm; 150 ppm; UAN-32, 32 % at 11.05 lb/gal (3.536 lb N per gallon); 25 lb N to apply.
  2. Result0.354 gpm (21.24 gph); 7.07 gal of product; 20 minutes.

A pivot pass

  1. Inputs10 lb N an acre; 40 acres; 6 h; 3.55 lb N per gallon; 600 gpm.
  2. Result112.7 gal at 18.78 gph; about 222 ppm N in the water — above 200, so spread it over a longer pass.

Per-acre product rates

  1. Light rate0.25 gal an acre on 125 acres over 21 h: 31.25 gal at 1.488 gph — below a 5.5–55 gph pump’s range, so dilute.
  2. UAN through a pivot8.5 gal an acre on 121.9 acres over 21.39 h: 1,036 gal at 48.44 gph.

Greenhouse stock and chlorine

  1. 1:200, 250 ppm, 15 % N44.51 oz per gallon of stock. 1:100, 450 ppm, 25 % N: 1.50 lb/gal. 10 oz/gal of a 20 % N fertilizer at 1:100 delivers 149.8 ppm.
  2. Chlorine3 ppm into 460 gpm with a 12.5 % product: 0.662 gph.
  3. Metric100 ppm N into 30 L/s with 0.4242 kg N per litre: 25.46 L/h.

Why density matters

ppm is by weight: milligrams of nutrient per kilogram of water. A gallon of UAN-32 weighs about 11.05 lb, not 8.34, so it carries 3.54 lb of nitrogen, not 2.67. A shortcut that treats product as weighing the same as water calls for 0.47 gpm where 0.354 gpm is right, and actually delivers about 199 ppm instead of 150. Enter the nitrogen per gallon from the label, or the percentage and density, and the calculator gets it right.

Common products. Check your label; values vary by maker.
ProductNutrientDensityNutrient per gallon
UAN-3232 % N11.05 lb/gal3.54 lb N
UAN-2828 % N10.67 lb/gal2.99 lb N
Sodium hypochlorite 12.5 %12.5 %near water (use “density = water”)about 1.04 lb

Stock tanks and injector ratios

A 1:100 injector puts one gallon of stock into every 100 gallons of water. Use the elemental percentage: potassium from K₂O × 0.83, phosphorus from P₂O₅ × 0.44. Enter the tank volume to get the fertilizer to weigh out. Check the delivered ppm with an EC meter, and measure the injector’s real ratio now and then. For drip zone flows, see the drip irrigation calculator and the emitter flow calculator.

Injector range and safety

Enter your pump’s accurate range to get a warning when the rate falls outside it. Below the range, dilute the product; above it, inject for longer. If the label sets a maximum line concentration, enter it too. Chemigation needs the backflow and interlock safety equipment your state and the product label require; follow the label. For pivot hours and acres, use the center pivot calculator; for the field’s flow, the system capacity calculator.

Mistakes to avoid

Treating product as water

Heavy liquids carry more nutrient per gallon. Use the label’s lb per gallon or the density.

Oxide % as elemental %

Labels list P₂O₅ and K₂O. Convert before using them for P or K ppm.

Short injections on a pivot

Injecting for less than the revolution covers only part of the circle.

Forgetting to flush

On drip, leave time to flush the lines after injecting; subtract it from the set time.

How we build and check this calculator

Every formula on this page names its source, and the code is tested against worked cases before every update.

  • Methods from recognised sources. Field methods follow UF/IFAS and University of Nebraska Extension; stock-tank methods follow UMass Extension. See the sources.
  • Tested against worked cases. Eleven cases run against the calculator code before every update, including the UF/IFAS, UMass and Nebraska examples, a chlorine injection, an out-of-range pump, a metric case and a line-concentration check. All must match.
  • Honest about limits. This page sets the injector; it doesn’t recommend how much fertilizer a crop needs.
  • Your entries stay on your device. The calculator runs in your browser. Nothing you type is sent anywhere; your inputs live only in the page address, so you can bookmark or share a result.
  • Corrections are welcome. If a number looks wrong, tell us. We check it against the sources, fix the page and update the date at the top.

Page history

Published. Methods, test cases and source links checked.

Questions

How do I calculate a fertigation injection rate?

Work out the nutrient the water must carry each minute (flow × 8.345 × ppm ÷ 1,000,000 in lb) and divide by the nutrient in each gallon of product. 150 ppm N in 1,000 gpm with UAN-32 at 3.54 lb N per gallon is about 0.354 gpm (21.2 gph).

How many gallons of UAN per acre for 10 lb of N?

Divide by the nitrogen per gallon. UAN-32 carries about 3.54–3.55 lb N per gallon, so 10 lb N is about 2.8 gallons an acre. Check your label.

What ppm of nitrogen should I fertigate at?

UF/IFAS suggests keeping nitrogen at or below 200 ppm in the water, with 150 ppm common. The calculator warns above 200 ppm.

How do I mix a stock tank for a 1:100 injector?

Ounces per gallon of stock = ppm × 100 ÷ (nutrient % × 74.89). For 150 ppm N with a 20 % N fertilizer that is about 10 oz per gallon of stock.

How long should I inject through a pivot?

Over the time the pivot takes to cover the area — the revolution hours for the arc. Spreading the product over the whole pass gives the most even application.

How do I check my injection pump?

Run it into a measuring jar for a timed minute and compare with the mL/min or oz/min result. Adjust the pump until they match.

When should I dilute the product?

When the injection rate is below the pump’s accurate range. Add water to the supply tank, recalculate with the diluted strength and the rate rises into range.

Sources

  1. University of Florida IFAS Extension, How to Calculate Fertigation Injection Rates for Commercial Blueberry Production (HS1197). The stepwise injection rate and time method and the 150–200 ppm N guidance; UAN-32 density 11.05 lb/gal.
  2. University of Florida IFAS Extension, Fertigating Potatoes Through Center-Pivot Irrigation (HS1361). A 40-acre pivot example (10 lb N per acre, 600 gpm, 6 h) and injector capacity range used as checks.
  3. UMass Extension Greenhouse Crops and Floriculture, Fertilizer Calculations for Greenhouse Crops. Stock strength for proportional injectors (conversion constants 75 for oz/gal, 1,200 for lb/gal, 10 for g/L) and worked examples used as checks.
  4. University of Nebraska–Lincoln CropWatch, How to Determine the Chemigation Injection Pump Setting for a Center Pivot. Setting the injection pump from the pivot’s acres per hour.
  5. ppm by mass balance with water at 8.345 lb/gal, the exact stock constants (74.89 and 1,198.3; UMass rounds to 75 and 1,200), line concentration % = gph × 100 ÷ (60 × gpm) and metric conversions are derived on this page. Washington State University’s chemigation worksheets use the same area- and concentration-based forms.

Links checked November 16, 2026. Two published shortcuts treat a gallon of product as weighing the same as water. With UAN-32 at 11.05 lb/gal that overstates the rate — 0.47 gpm into 1,000 gpm delivers about 199 ppm N, not 150 — so this page uses product strength by weight. Choosing “density = water” reproduces the shortcut (0.47 gpm).