Irrigation Friction Loss Calculator

Find how much pressure an irrigation pipe loses to friction. Pick the pipe by class and size instead of looking up its inside diameter, add pieces of different size or flow, a fittings allowance and the elevation change, or work out the loss along a sprinkler lateral where every head takes its share.

Friction loss calculator

Choose your pipe
Quick picks

1Pipe run

Add pieces when the size or flow changes along the run.

in

Metric pipe IDs vary by PN class; enter the ID from the spec.

GPM
ft

Set by the pipe; edit for old or rough pipe.

in
GPM
ft
in
GPM
ft
in
GPM
ft
in
GPM
ft
in
GPM
ft

2Fittings and elevation

%
ft

From a fittings table; counted at the first piece’s loss rate.

ft

Shown on its own line; it isn’t friction.

psi

Optional: flags a run that uses more than a quarter of it.

See the friction loss ↓

How the calculator works

Every foot of pipe costs a little pressure. How much depends on the flow, the inside diameter and how smooth the pipe is.

  • Loss ratepsi per 100 ft = 0.2083 × (100 ÷ C)^1.852 × Q^1.852 ÷ d^4.8655 × 0.433 (Q in GPM, d inside diameter in inches)
  • Pipe losspsi per 100 ft × length ÷ 100, added up piece by piece
  • Fittingspipe loss × allowance %, or psi per 100 ft × equivalent length ÷ 100
  • VelocityV (ft/s) = 0.4085 × Q ÷ d²
  • Lateralloss = F × (loss if the full flow ran the whole length), F = 1 ÷ (m + 1) + 1 ÷ 2N + √(m − 1) ÷ 6N², m = 1.852
  • Elevation0.433 psi per foot of rise, shown separately (+ uphill, − downhill)
  • Headfeet of water = psi × 2.31

Choose the pipe by class and size and the calculator uses its inside diameter and C. For metric (PN-rated) pipe, IDs vary by class, so pick “Other” and enter the ID.

Worked examples

A 1-in mainline

  1. Inputs1-in Sch 40 PVC (ID 1.049 in, C 150), 12 GPM, 150 ft, 10 % for fittings.
  2. Pipe3.36 psi per 100 ft × 1.5 = 5.04 psi; fittings 0.50 psi.
  3. Result5.55 psi at 4.45 ft/s, just under the 5 ft/s limit.

A long 1-1/2-in main

  1. Inputs1-1/2-in Class 200 (ID 1.719 in), 30 GPM, 400 ft, 10 % fittings.
  2. Result1.66 psi per 100 ft; 6.64 + 0.66 = 7.30 psi at 4.15 ft/s.

A spray lateral

  1. Inputs1-in Sch 40 with 6 heads at 3 GPM, 15 ft apart (90 ft).
  2. Full flow18 GPM over 90 ft would lose 6.41 psi.
  3. With outletsF = 0.438, so the lateral loses 2.81 psi. Inlet velocity 6.68 ft/s is high; consider 1-1/4 in.

Metric

  1. Inputs2.0 L/s (31.7 GPM) through 50 mm ID pipe, 100 m.
  2. Result21.5 kPa (3.12 psi) at 1.02 m/s.

Friction loss chart (psi per 100 ft)

PVC, C 150. Values above 5 ft/s are marked with *.
Flow3/4 Sch 401 Sch 401-1/4 Sch 401-1/2 Sch 401 Class 2001-1/4 Class 200
5 GPM2.150.660.170.080.360.12
10 GPM7.76*2.400.630.301.300.42
15 GPM16.45*5.08*1.340.632.750.89
20 GPM28.03*8.66*2.281.084.69*1.51
30 GPM59.39*18.35*4.83*2.289.93*3.20*

Sch 40 vs Class 200 vs poly pipe

Inside diameters (in) and C values used here.
SizeSch 40 PVCClass 200 PVCClass 160 PVCPECopper L
3/4 in0.8240.930—0.8240.785
1 in1.0491.1901.1951.0491.025
1-1/4 in1.3801.5021.5321.3801.265
1-1/2 in1.6101.7191.7541.610—
2 in2.0672.1492.1922.067—
C value150150150140140

Need to choose a size rather than check one? The pipe size calculator picks the smallest size that keeps velocity and loss down.

Laterals with outlets

On a lateral, each head takes its share of the water, so the pipe carries less and less flow toward the end. The Christiansen F factor accounts for that: with 6 outlets it is 0.438, so the loss is under half of what the full flow would lose over the whole length. Keep lateral loss within about 20 % of head pressure, 10 % for the most even watering. Put the result into the pressure budget to see what reaches the last head.

Velocity and water hammer

Velocity ratings.
VelocityRatingWhat to do
5 ft/s or lessWithin the common design limitFine.
5–7.5 ft/sHigh: water-hammer riskConsider one size up.
7.5–10 ft/sToo fastUpsize.
Over 10 ft/sUnsafeUpsize; never run this fast.

Mistakes to avoid

Nominal size as the ID

“1-in” pipe is about 1.05 in inside for Sch 40 and 1.19 in for Class 200. Using 1.000 overstates the loss.

Full flow on a lateral

Running the whole zone flow through the whole lateral more than doubles the loss. Use the lateral tab.

Mixing in the valves

Valves, meters and backflow devices have their own loss charts; add them in the pressure budget.

Forgetting elevation

Each foot uphill costs 0.433 psi, often more than the friction itself.

How we build and check this calculator

Every formula on this page names its source, and the code is tested against worked cases before every update.

  • Methods from recognised sources. Hazen-Williams and C values follow extension and manufacturer charts; the velocity limit follows Texas A&M Extension. See the sources.
  • Tested against worked cases. Seven cases run against the calculator code before every update: a 1-in main, the UF/IFAS published example, a Class 200 main, a PE run, a spray lateral, a metric pipe and an unsafe velocity. All must match.
  • Honest about limits. C values are for new pipe. Old, scaled or poorly joined pipe loses more.
  • Your entries stay on your device. The calculator runs in your browser. Nothing you type is sent anywhere; your inputs live only in the page address, so you can bookmark or share a result.
  • Corrections are welcome. If a number looks wrong, tell us. We check it against the sources, fix the page and update the date at the top.

Page history

Published. Methods, test cases and source links checked.

Questions

What is friction loss in irrigation pipe?

It is the pressure water loses as it rubs along the pipe wall and through fittings. It grows quickly with flow, roughly with the flow to the power 1.85, so doubling the flow nearly quadruples the loss. Pressure lost in the pipe is pressure the sprinklers don’t get.

How do I read a PVC friction loss chart?

Find your pipe size across the top and your flow down the side; the box gives psi lost per 100 ft. Multiply by your length ÷ 100. This calculator does the same with the Hazen-Williams equation, so any flow and length work.

Sch 40, Class 200 or poly pipe, which loses less?

At the same nominal size, Class 200 PVC loses the least because its thin wall leaves a wider bore. Sch 40 has a narrower bore. PE has the same bore as Sch 40 but a rougher wall (C 140), so 1-in PE at 10 GPM loses about 2.73 psi per 100 ft against 2.40 for Sch 40.

What C value should I use?

150 for new PVC, 140 for PE and copper, about 100 for galvanised steel. Older or scaled pipe is rougher; lower C to match.

How much pressure loss is acceptable in a lateral?

A common rule is no more than 20 % of the heads’ operating pressure; many design guides aim for 10 %. Above that, the last heads run noticeably weaker than the first.

How much do fittings add?

A common estimate is 10 % of the pipe loss for a typical run. With many elbows and tees, use 20 %, or add up the equivalent length of each fitting from a fittings table.

Why keep velocity under 5 ft/s?

Faster water raises friction steeply and causes water hammer when valves close, which can split plastic pipe. 5 ft/s is the common design limit for PVC; experts agree never to exceed 10 ft/s.

Sources

  1. University of Florida IFAS Extension, Hydraulic Considerations for Citrus Microirrigation Systems (CH156). The Hazen-Williams equation and friction tables for irrigation pipe, used here as a published check (1-in Sch 40 at 8 GPM, 2.97 ft/s and 1.59 psi per 100 ft).
  2. Hunter Industries, Handbook of Technical Irrigation Information. Irrigation Association friction loss and velocity charts, C values, and the dynamic pressure method with pipe, fittings and elevation losses.
  3. The Toro Company (ToroAg), Hazen-Williams Equation. Roughness coefficient C values for new pipe and design (PVC 150; copper 140).
  4. Texas A&M AgriLife Extension (Fipps), Calculating Horsepower Requirements and Sizing Irrigation Supply Pipelines (EB-6011). The 5 ft/s rule for PVC to limit water hammer, never above 10 ft/s, and velocity from flow and inside diameter.
  5. The pipe inside diameters (ASTM D1785 Sch 40 and the ASTM D2241 minimum-wall rule for Class 200 and 160), the Christiansen multiple-outlet factor (Christiansen, 1942, m = 1.852) and all unit conversions are derived on this page.

Links checked November 15, 2026. The equation reproduces the UF/IFAS example exactly. A widely shared table lists 8.12 psi per 100 ft for 1-in Sch 40 at 18 GPM; that matches C = 140, while C = 150 gives 7.12. This page shows the C it uses.