Sprinkler Precipitation Rate Calculator

Work out how many inches (or millimetres) of water a sprinkler zone puts down per hour. Use the zone’s total flow and area, one head’s flow, arc and spacing, or the readings from a catch-cup test, then compare the rate with what your soil can absorb.

Precipitation rate calculator

Choose what you know
Quick picks

1The zone

GPM

Read it at the water meter with only this zone running, or add up the nozzle flows.

sq ft

Just the area this zone waters, in square feet.

2Soil check

Compares the rate with how fast your soil soaks water in.

in/hr

Pick a soil above, or type a rate from an infiltration test.

How the calculator works

Precipitation rate is how fast a zone puts water down, in inches (or millimetres) per hour, like rainfall. It is the number you need to turn a watering depth into minutes.

You can get it three ways. If you know the zone’s total flow and the area it covers, divide one by the other. If you know one head’s flow and how far apart the heads are, work out the area each head waters. If you have run a cup test, use what the cups caught.

  • Zone flow and areaPR (in/hr) = 96.25 × total GPM ÷ area (sq ft) · PR (mm/hr) = 60 × L/min ÷ area (m²)
  • Where 96.25 comes from231 in³ per gallon ÷ 144 in² per sq ft × 60 minutes per hour
  • One head, by spacingPR = 96.25 × Qeq ÷ (S × L), with Qeq = head GPM × 360 ÷ arc
  • Row spacingsquare L = S · rectangle L as measured · triangle L = 0.866 × S
  • Cup testPR = average depth ÷ (minutes ÷ 60) · depth from mL = mL × 0.0610237 ÷ (π × D² ÷ 4), D in inches
  • Flow densityGPM per acre = GPM × 43,560 ÷ area (sq ft)

One head type per zone is assumed. If the zone mixes sprays and rotors, no single rate describes it; split it with the sprinkler zone calculator.

Worked examples

Spray heads on a 15 ft square

  1. InputsFull-circle spray heads using 1.85 GPM, 15 ft apart in a square.
  2. Area per head15 × 15 = 225 sq ft.
  3. Result96.25 × 1.85 ÷ 225 = 0.79 in/hr. That is low for sprays (usually 1.0–2.0), so check the nozzle and the spacing.

A whole zone from the water meter

  1. InputsThe meter shows 12 GPM with only this zone on; it waters 1,200 sq ft.
  2. Formula96.25 × 12 ÷ 1,200 = 0.9625.
  3. Result0.96 in/hr, or 12 × 43,560 ÷ 1,200 = 436 GPM per acre.

A 12-cup test

  1. InputsCups read 0.30, 0.25, 0.35, 0.20, 0.28, 0.32, 0.22, 0.30, 0.27, 0.31, 0.24 and 0.29 in after 15 minutes.
  2. Average3.33 ÷ 12 = 0.278 in.
  3. Result0.278 ÷ (15 ÷ 60) = 1.11 in/hr. Divide by hours, not minutes: 15 minutes is 0.25 hours.

Metric zone

  1. Inputs30 L/min over 50 m².
  2. Result60 × 30 ÷ 50 = 36.0 mm/hr (1.42 in/hr).

Typical precipitation rates by head type

Typical ranges at head-to-head spacing and normal pressure. Your nozzle chart gives the exact figure.
Head typein/hrmm/hrInches in 15 minutes
Fixed spray1.0–2.025–510.25–0.50
Rotary nozzle (multi-stream)0.4–0.610–150.10–0.15
Gear-driven rotor0.3–0.88–200.08–0.20
Impact sprinkler0.2–0.65–150.05–0.15

Sprays water three to five times faster than rotors. That is why the two never share a zone: a run time that suits one floods or starves the other.

How to run a catch-cup test

  1. CupsUse 12–24 identical, straight-sided cups or cans. Tuna cans and purpose-made catch cups both work.
  2. LayoutSet them in a grid across the zone, about one-third of the head spacing from each head and halfway between heads, not right next to a head.
  3. RunRun the zone for 15–20 minutes on a calm morning, at normal pressure.
  4. ReadMeasure the depth with a ruler, or pour each into a measuring cylinder for millilitres. Enter 0 for a dry cup.

Millilitres are more precise for small catches. Enter the cup’s opening diameter and the calculator converts each reading to depth. With 8 or more cups, a link under the chart carries the readings straight to the distribution uniformity calculator, so the same test tells you how evenly the zone waters.

Matched precipitation and part-circle heads

A half-circle head throws over half the area of a full circle. If it uses the same flow, it puts down twice the water. Matched nozzles fix this by giving a half circle half the flow and a quarter circle a quarter.

In the spacing tab, enter the part-circle head’s own flow and its arc. The calculator turns it into a full-circle equivalent (flow × 360 ÷ arc). Add the full-circle heads’ flow and it checks that the two are within 15 %. A quarter-circle head on a full-circle nozzle (1.85 GPM at 90°) works out to 7.40 GPM equivalent and 3.17 in/hr, four times the rest of the zone. To pick matched flows, use the arc tab of the nozzle flow calculator.

Precipitation rate and your soil

Water that lands faster than the soil absorbs it runs off. Pick your soil and the calculator compares the two rates.

What the comparison means.
ResultWhat it meansWhat to do
Rate at or below intakeWater soaks in as it lands.Run in one go.
Up to 3 × intakePuddles form before the run ends.Use cycle and soak: two or three shorter runs.
Over 3 × intakeMost of a long run is lost as runoff.Short cycles, or lower-rate nozzles.

The run time calculator takes this rate and works out the minutes per cycle and the soak time.

Mistakes to avoid

Dividing by minutes

A 15-minute cup test that caught 0.278 in is 1.11 in/hr, not 0.019. Always divide the depth by the hours run.

GPH for GPM

Drip and bubbler flows are often in gallons per hour. One GPM is 60 GPH. A rate above 4 in/hr usually means the units are mixed up.

Part-circle flow as full circle

Enter the nozzle’s real flow and its arc. Typing the full-circle figure for a half head halves the rate you get.

Whole yard as the area

Use only the area this zone waters. The yard total gives a rate far too low and run times far too long.

How we build and check this calculator

Every formula on this page names its source, and the code is tested against worked cases before every update.

  • Methods from recognised sources. The spacing and area formulas follow Rain Bird and Toro technical data; the cup test follows the Irrigation Association’s field audit method. The 96.25 constant is derived on the page. See the sources.
  • Tested against worked cases. Nine cases run against the calculator code before every update: zone flow and area, sprays, rotors and impacts by spacing, half- and quarter-circle heads, a 12-cup depth test, an 8-cup millilitre test and a metric zone. All must match.
  • Honest about limits. The rate is an average. Wind, low pressure and poor spacing make some spots wetter and others drier; a cup test and a DU check show how much.
  • Your entries stay on your device. The calculator runs in your browser. Nothing you type is sent anywhere; your inputs live only in the page address, so you can bookmark or share a result.
  • Corrections are welcome. If a number looks wrong, tell us. We check it against the sources, fix the page and update the date at the top.

Page history

Published. Methods, test cases and source links checked.

Questions

What is a good precipitation rate for a lawn sprinkler?

It depends on the head and the soil. Fixed sprays usually put down 1.0–2.0 in/hr, rotors 0.3–0.8 and rotary nozzles 0.4–0.6. A good rate is one your soil can take in; clay absorbs only about 0.1–0.2 in/hr, so fast sprays on clay need short cycles.

How do I measure my sprinkler’s precipitation rate with cups?

Set 12–24 straight-sided cups on a grid across the zone, run it for 15–20 minutes, and measure the water in each. Enter the readings and the run time. The average depth divided by the run time in hours is the rate.

Why is the constant 96.25 (or 96.3)?

One gallon is 231 cubic inches and one square foot is 144 square inches, so a gallon spread over a square foot is 1.604 in deep. Per hour that is 1.604 × 60 = 96.25. Many catalogues round it to 96.3; the difference is under 0.1 %.

Should part-circle heads have lower flow than full circles?

Yes. A half-circle head covers half the area, so it should use half the flow of the full circle, and a quarter circle a quarter. Then every head puts down the same rate. This is called matched precipitation; the spacing tab checks it for you.

How do I convert precipitation rate to run time?

Divide the depth you want by the rate and multiply by 60. At 1.6 in/hr, 0.5 in takes about 19 minutes. The run time calculator does this with soil checks and cycle-and-soak.

Why do my cup test and the catalogue rate differ?

The catalogue assumes ideal spacing, pressure and no wind. Real zones have worn or mixed nozzles, low pressure at the far end and heads that are tilted or blocked. Trust the cup test for scheduling, and use its readings to check distribution uniformity.

What if the rate is higher than my soil can absorb?

Water will pond and run off before the root zone fills. Split the run into two or three short cycles with a soak in between, or switch to lower-rate nozzles such as rotary nozzles.

Sources

  1. Rain Bird Corporation, Irrigation Design Tip: Sprinkler Spacing Patterns. Precipitation rate from head flow and the area of one spacing, the triangular row height and matched precipitation.
  2. Rain Bird Corporation, Precipitation rate equations (catalogue technical data). The 96.3 constant for inches per hour from GPM and square feet, the metric form, and row spacing = 0.866 × spacing for triangles.
  3. Rain Bird Corporation, Golf irrigation design appendix. Square and triangular precipitation rate with the head’s arc, 96.3 × GPM × 360 ÷ (S × L × arc).
  4. Rain Bird Corporation, Technical Newsletter, Spring 2001: Sprinkler Spacing. PR = 96.3 × GPM ÷ (S × L), matched precipitation, and keeping sprinkler types on separate zones.
  5. The Toro Company, FLX34 Series sprinkler specification sheet. Square, triangular and area-and-flow precipitation rate formulas using 96.3.
  6. Irrigation Association, Using Distribution Uniformity to Evaluate the Quality of a Sprinkler System (Mecham, 2004). Catch-can testing in the field, the basis of the cup-test mode.
  7. The 96.25 constant, the millilitre-to-depth conversion, the minutes-to-hours step and all unit conversions are derived on this page. Typical rates by head type summarise published nozzle charts; your own chart takes priority.

Links checked November 15, 2026. The 96.25 constant was derived from 231 in³ per US gallon and 144 in² per square foot, and checked against the 96.3 used in manufacturer catalogues.