Irrigation Schedule Calculator

Find how often to water so the roots are refilled before plants get stressed, without overfilling the soil. Get the number of days between waterings, or the fewest watering days a week your soil allows within your local watering rules, plus how much to apply each time.

Irrigation schedule calculator

Choose how you know the water need
Quick picks

1Soil and roots

Sets a typical available water capacity; edit the number if you know yours.

in/ft

Water a foot (or metre) of soil holds for plants. Layered or measured soil? Work it out here.

Sets a typical root depth you can change.

in

Depth where most of the roots are. Dig or probe to check.

2Water use

in/day

Your plants’ daily use. Find it from local ETo.

in

Optional. Add up daily use since the last good watering or soaking rain to see days until the next one.

%

Share of the stored water plants may use before you water again. 50 % suits most lawns and crops.

%

Sprinklers 70–80 %, drip 85–95 %. Leave it blank for 100 %.

See your schedule ↓

How the calculator works

The soil around the roots is a water bank. Plants draw it down every day; you water when about half is gone. The time that takes is your watering interval.

This is the soil water balance, often called checkbook scheduling. The calculator works out how much water your root zone holds, how much of it plants can use comfortably, and how long that lasts at your daily water use. Then it tells you how much to put back each time.

  • Total available waterTAW = available water capacity × root depth (in/ft × in ÷ 12, or mm/m × m)
  • Readily available waterRAW = MAD × TAW
  • Interval, daysinterval = RAW ÷ daily water use, rounded down to a whole day (at least 1)
  • Depth each timenet = daily use × interval · gross = net ÷ efficiency
  • Weekly modedays needed = weekly need ÷ RAW, rounded up · depth each time = weekly need ÷ days
  • Days until next(RAW − water already used) ÷ daily use, rounded down; 0 means water today

Rounding the interval down and the days up keeps every watering inside what the soil can hold. The two modes answer the same question from different starting points: daily use (from a crop coefficient and ETo) or a weekly need (a lawn’s “inch a week”).

Don’t know your daily use? Get it from local ETo with the water requirement calculator. Layered soil, rocks or lab values? Work out the storage with the available water capacity calculator and enter its in/ft figure here.

Worked examples

A lawn on loam

  1. InputsLoam (2.00 in/ft), 6 in roots, MAD 50 %, water use 0.20 in/day, efficiency 75 %.
  2. Soil waterTAW = 2.00 × 6 ÷ 12 = 1.00 in; RAW = 0.50 × 1.00 = 0.50 in.
  3. Interval0.50 ÷ 0.20 = 2.5 → every 2 days, about 3.5 times a week.
  4. Depth0.20 × 2 = 0.40 in net; 0.40 ÷ 0.75 = 0.53 in to put down each time.

A vegetable bed, already part-way dry

  1. InputsSandy loam (1.30 in/ft), 12 in roots, MAD 50 %, 0.25 in/day, 0.30 in already used since the last soaking.
  2. Soil waterTAW = 1.30 in; RAW = 0.65 in. Interval 0.65 ÷ 0.25 = 2.6 → every 2 days.
  3. Next watering(0.65 − 0.30) ÷ 0.25 = 1.4 → in 1 day.

Two watering days a week

  1. InputsLoam, 8 in roots, MAD 50 %, a weekly need of 1.20 in, 2 allowed days, efficiency 75 %.
  2. Soil waterTAW = 2.00 × 8 ÷ 12 = 1.33 in; RAW = 0.67 in.
  3. Days1.20 ÷ 0.67 = 1.8 → 2 days, which fits the restriction.
  4. Depth1.20 ÷ 2 = 0.60 in net, 0.80 in gross each watering day.

How often to water by soil type

Soil texture sets how much water a foot of soil holds for plants. Silt loams hold the most; sands hold the least, so they need water most often.

Available water capacity defaults and the resulting interval at MAD 50 %. Lawn: 6 in roots. Vegetables: 12 in roots. Values are typical; your soil may differ.
Soil texturein/ft (mm/m)Lawn at 0.20 in/dayLawn at 0.15 in/dayVegetables at 0.20 in/day
Sand0.75 (62)1 day1 day1 day
Loamy sand1.15 (96)1 day1 day2 days
Sandy loam1.30 (108)1 day2 days3 days
Fine sandy loam1.75 (146)2 days2 days4 days
Loam2.00 (167)2 days3 days5 days
Silt loam2.25 (187)2 days3 days5 days
Silty clay loam1.90 (158)2 days3 days4 days
Clay loam1.80 (150)2 days3 days4 days
Silty clay1.60 (133)2 days2 days4 days
Clay1.35 (112)1 day2 days3 days

The defaults are midpoints of the University of Nebraska–Lincoln ranges by texture; loam and clay loam use Nebraska Extension’s single values (2.0 and 1.8 in/ft), because the range table doesn’t list them. Other sources group soils more coarsely (UC IPM uses 1.0 for sand, 1.5 for sandy loam and 2.2 for loam through clay), so if you have a soil survey or a lab result, type it in.

Clay holds less available water than loam because much of its water clings too tightly for roots to pull out. Clay also soaks water in slowly, so a deep watering on clay often needs the cycle and soak split in the run time calculator.

How often to water in summer vs spring and fall

The soil holds the same water all year; what changes is how fast plants use it. In spring and fall, daily use is often half the summer peak, so the interval doubles. That is why most controllers keep the run time and change the watering days.

Under every soil-mode result there is a seasonal table for your soil and roots. For a lawn on loam (6 in roots, MAD 50 %), it runs from every 5 days at 0.10 in/day of use to every 3 days at 0.15, every 2 days at 0.20–0.25, and daily at 0.30 and above. Re-check the schedule when the weather changes, or use your daily use from local ETo each week.

Allowable depletion and root depth

What management allowable depletion (MAD) means

MAD is how much of the stored water you let plants use before watering. FAO-56 calls it the depletion fraction p and gives 0.50 as the common value for many crops; it runs from about 0.30 for shallow-rooted plants in hot weather to 0.70 for deep-rooted ones in cool weather. Above about 65 % lawns and vegetables start to show stress, so the calculator warns you.

How root depth changes the schedule

Storage grows in step with root depth. Typical depths are about 6 in for turf, 8–12 in for flowers and vegetables, 12–24 in for shrubs and trees, and 3 ft or more for field crops. Probe or dig to see where most roots are: shallow-watered lawns often root only 2 to 4 in, which forces daily watering. Watering deeply and less often lets roots go deeper and stretches the interval.

How to stay within a 2-day-a-week watering restriction

Pick your allowed days in the weekly mode. If the soil can hold the week’s need in that many waterings, the calculator gives you the depth for each; if not, it says so and by how much.

The check is simple: each watering must fit in the readily available water. A lawn on loam with 6 in roots has 0.50 in of RAW, so two waterings hold 1.00 in, enough for most of the summer. On sand with 6 in roots, RAW is only 0.19 in, so even daily watering can’t deliver 1.4 in without some loss.

If your restriction is too tight for your soil: split each watering into short cycles so less runs off, mulch beds, raise the mowing height and water deeply to grow deeper roots, or accept some summer stress. Hosepipe bans and odd/even rules work the same way: count the days you may water.

How to read your result

Interval ranges and what they mean.
IntervalWhat it meansWhat to do
1 dayThe root zone holds very little: sandy soil or shallow roots.Water lightly each day, or deepen roots and improve the soil; check for runoff.
2–4 daysA typical summer interval for lawns and gardens.Set the days, then the minutes with the run time calculator.
5–10 daysDeep, infrequent watering.Good for trees, shrubs and field crops.
Over 10 daysLow demand or deep roots.Confirm with a soil probe before you rely on it.
Irrigate nowThe water already used is at or past the allowable depletion.Water today, then follow the interval.

Rain resets the clock. Credit what reached the roots with the effective rainfall calculator, which also tells you how many days you can skip.

Signs the schedule is wrong

Footprints stay, grass turns blue-gray

The lawn is running dry before the next watering. Shorten the interval or check the root depth.

Puddles, runoff, soggy soil

Too much at once, or too often. Use the cycle split, or lengthen the interval.

Use a screwdriver test

A day after watering, a screwdriver should push easily to the bottom of the roots. If it stops short, water went too shallow.

Water early in the morning

Less is lost to wind and evaporation, and leaves dry before evening.

How we build and check this calculator

Every number on this page comes from a formula you can see and a source you can open, and the code is tested against worked cases before every update.

  • Methods from recognised sources. TAW, RAW and the depletion fraction follow FAO-56. Soil water defaults follow University of Nebraska–Lincoln tables and Nebraska Extension. Root depths follow Nebraska Extension guidance. See the sources.
  • Tested against worked cases. Seven test cases run against the calculator code before every update: a loam lawn, a vegetable bed with water already used, sand with shallow roots, a 2-day restriction, a metric case, very shallow roots on sand and the seasonal table. All must match.
  • Honest about limits. The schedule assumes one soil, steady weather and a root zone refilled each time. Layered soils, slopes, shade and rain all shift it; check with a soil probe.
  • Your entries stay on your device. The calculator runs in your browser. Nothing you type is sent anywhere; your inputs live only in the page address, so you can bookmark or share a result.
  • Corrections are welcome. If a number looks wrong, tell us. We check it against the sources, fix the page and update the date at the top.

Page history

Published. Method, soil defaults, test cases and source links checked.

Questions

How often should I water my lawn in summer?

For most lawns on loam with 6 in roots, every 2 to 3 days in midsummer and every 4 to 7 days in spring and fall. Sandy soil may need daily watering at peak; clay and deeper roots stretch the interval. The exact answer is the soil water your roots can use divided by the daily water use.

Why does sandy soil need watering more often than clay?

Sand holds about 0.75 in of plant-available water per foot of soil; loam and silt loam hold 2 to 2.25 in. With the same roots and the same weather, a sandy lawn runs through its store in a third of the time, so it needs smaller, more frequent waterings.

What does management allowable depletion (MAD) mean?

MAD is the share of the stored water you let plants use before watering again, set so they never get stressed. 50 % is the common choice for lawns and most crops. A lower MAD means more frequent, lighter waterings; a higher one saves visits but risks stress.

What does deep and infrequent watering mean in days?

It means refilling the whole root zone each time, then waiting until about half of it is used. For a lawn on loam that is usually every 2 to 4 days in summer; for shrubs and trees with 18 to 24 in roots, about every 5 to 10 days.

How do I stay within a 2-day-a-week watering restriction?

Choose 2 allowed days in the weekly mode. If your soil can hold half the week’s water in one go, you’re fine; the calculator tells you how much to put down each time. If it can’t, it warns you, and the fix is cycle and soak, mulch, deeper roots or accepting a little stress.

Does root depth change the schedule?

Yes, in step with it. Doubling the root depth doubles the water the soil can store for the plant, so the same daily use takes twice as long to drain it. Deep watering trains roots to grow deeper, which in turn lets you water less often.

How much should I water each time?

Refill what was used, which is daily use × the interval, then divide by the system efficiency. The result gives this as the gross depth per watering. Turn it into controller minutes with the run time calculator.

Sources

  1. Food and Agriculture Organization of the United Nations (FAO), Crop Evapotranspiration, Irrigation and Drainage Paper 56, Chapter 8: ETc under soil water stress conditions. Total available water (TAW), readily available water RAW = p × TAW, and p = 0.50 as the common value for many crops.
  2. University of Nebraska–Lincoln, Plant and Soil Sciences eLibrary, Soil Water (Table 2.6, available water capacity by texture). Available water capacity ranges by texture; the soil defaults are midpoints of these ranges.
  3. Nebraska Extension, Irrigation Scheduling Strategies When Using Soil Water Data (EC3036, S. R. Melvin and D. L. Martin, 2018). Single values by texture, including loam 2.0 and clay loam 1.8 in/ft, the two classes the range table does not list.
  4. University of Nebraska–Lincoln, Plant and Soil Sciences eLibrary, Irrigation Chapter 9: Soil Water Balance. The checkbook method of tracking root-zone water between irrigations.
  5. University of Florida IFAS Extension, Crop Water Use and Irrigation Scheduling Guide for North Florida (SS491). TAW = water-holding capacity × rooting depth ÷ 12, scheduled at 50 % allowable depletion.
  6. Nebraska Extension, Don’t fight with your irrigation system – become an irrigation “master”!. Root depths of about 6 in for turf, 8–12 in for ornamentals and vegetables and 12–24 in for trees and shrubs, and deep, infrequent watering.
  7. University of California Statewide IPM Program, Calculating available water-holding capacity of a soil profile (potato guidelines, figure 17). A second set of texture values (sand 1.0, sandy loam 1.5, loam to clay 2.2 in/ft), showing how sources differ.
  8. The interval, waterings per week, days until the next watering and the weekly split are derived on this page from TAW and RAW.

Links checked November 15, 2026. Published water-holding values differ by source and by soil; the defaults are typical values, and you can type your own from a soil survey or a lab test.

Related guides