Available Water Capacity Calculator
Find how many inches of water the soil around your roots can store for plants. Pick a soil texture or enter lab field capacity and wilting point, or build a profile of up to four layers. You get total and readily available water, and the same storage in gallons.
Available water capacity calculator
How the calculator works
Available water capacity is how much water a foot of soil holds for plants. Multiply it by the depth of the roots and you have the root zone’s water store, the total available water (TAW).
That store is what plants live on between waterings. Knowing it tells you how much to put back each time and, with the daily water use, how often. The calculator works it out for one soil or for a profile of up to four layers.
- From textureAWC from the texture table, in in/ft (mm/m), editable
- From lab valuesAWC (in/ft) = (field capacity % − wilting point %) ÷ 100 × 12 · in mm/m: (FC − WP) × 10
- Rock correctioneffective AWC = AWC × (1 − rock % ÷ 100)
- One soilTAW = effective AWC × root depth (in) ÷ 12
- Layerseach layer counts only down to the root depth: storage = depth counted ÷ 12 × AWC; TAW = sum of the layers
- Readily availableRAW = MAD × TAW
- Volumegal per 1,000 sq ft = TAW × 1,000 × 0.623 · acre-inches per acre = TAW in inches · L per m² = TAW in mm
The result also shows the typical intake rate of the top soil, how fast water soaks in. Storage tells you how much to apply; intake tells you how fast you can apply it before water runs off. The run time calculator uses intake for its cycle and soak split.
Worked examples
A foot of loam
- InputsLoam (2.00 in/ft), 12 in roots, MAD 50 %, no rock.
- TAW2.00 × 12 ÷ 12 = 2.00 in, or 1,246 gal per 1,000 sq ft.
- RAW50 % × 2.00 = 1.00 in.
A layered profile cut at the root depth
- InputsRoot depth 24 in. 8 in of silt loam (2.25 in/ft), 10 in of silty clay loam (1.90), 30 in of clay (1.35).
- Layers8 ÷ 12 × 2.25 = 1.50 in; 10 ÷ 12 × 1.90 = 1.58 in; the clay starts at 18 in, so only 6 in counts: 6 ÷ 12 × 1.35 = 0.68 in.
- TotalTAW = 3.76 in; RAW at 50 % = 1.88 in. The clay below 24 in is left out because no roots reach it.
Lab values
- InputsField capacity 30 %, wilting point 14 % (by volume), 18 in roots, MAD 40 %.
- AWC(30 − 14) ÷ 100 × 12 = 1.92 in/ft.
- TAW1.92 × 18 ÷ 12 = 2.88 in; RAW = 40 % × 2.88 = 1.15 in.
Available water capacity by soil texture
Silt loams hold the most plant-available water, about 2.25 in per foot; sands hold the least, under 1 in. The calculator’s defaults sit inside the published ranges.
| Texture | Default, in/ft | mm/m | Published range, in/ft | gal per 1,000 sq ft per foot | Intake, in/hr |
|---|---|---|---|---|---|
| Sand | 0.75 | 62 | 0.25–1.00 | 467 | 1.0 |
| Loamy sand | 1.15 | 96 | 1.10–1.20 | 716 | 0.8 |
| Sandy loam | 1.30 | 108 | 1.25–1.40 | 810 | 0.6 |
| Fine sandy loam | 1.75 | 146 | 1.50–2.00 | 1,090 | 0.6 |
| Loam | 2.00 | 167 | 2.0 (single value) | 1,246 | 0.4 |
| Silt loam | 2.25 | 187 | 2.00–2.50 | 1,402 | 0.3 |
| Silty clay loam | 1.90 | 158 | 1.80–2.00 | 1,184 | 0.2 |
| Clay loam | 1.80 | 150 | 1.8 (single value) | 1,121 | 0.2 |
| Silty clay | 1.60 | 133 | 1.50–1.70 | 997 | 0.1 |
| Clay | 1.35 | 112 | 1.20–1.50 | 841 | 0.1 |
Sources disagree. The UC IPM table groups loam, silt loam and clay together at 2.2 in/ft and uses 1.0 for sand and 1.5 for sandy loam. Organic matter and structure matter too: a well-mulched garden loam can hold more than the table says, a compacted one less. For your own ground, the Web Soil Survey value beats any texture average. Class names follow the USDA texture triangle, which differs slightly from UK and European systems.
Field capacity and wilting point
After a soaking, water drains out of the big pores for a day or two. What stays is field capacity. As plants drink, the soil dries until the remaining water clings too tightly to pull out; that is the permanent wilting point. Available water capacity is the difference between the two.
Labs measure them as water content by volume at about 1/3 bar (field capacity) and 15 bar (wilting point). Enter both in the “Lab field capacity and wilting point” option. Be sure they are by volume: values by weight look smaller for sands and larger for peat, and give the wrong answer. If the difference works out above 3 in/ft, the calculator asks you to check the units.
How to calculate available water for a layered soil
Most soils change with depth: a loamy topsoil over a clay subsoil, or silt over sand. Work layer by layer from the surface: thickness × capacity for each, stopping at the root depth, then add them up. The layered mode does this and tells you how much of each layer it counted.
Two things to watch. A layer that crosses the root depth only counts down to the roots. And if your layers stop short of the root depth, the calculator counts only the depth you entered and says so, rather than guessing what lies below. A dense clay pan or bedrock that roots can’t enter should end the profile: set the root depth to its top.
Readily available water vs total available water
Plants can pull water out all the way to the wilting point, but the last of it comes slowly and they suffer. Irrigation aims to refill the soil once a share of the store, the management allowable depletion (MAD), is gone. That share of TAW is the readily available water (RAW). FAO-56 uses 0.50 as the common value for many crops.
RAW is the depth to refill each time, before losses. Take it to the irrigation schedule calculator for how often to water, and to the run time calculator for how many minutes.
How rocks and gravel reduce water storage
Stones take up room in the soil and hold no water for plants. Enter the share of the soil volume that is gravel, cobbles or rock, and the capacity drops in proportion: 20 % rock means 20 % less storage. Above about 35 %, storage is small enough that you will water noticeably more often. Soil surveys list rock fragments by layer; on site, sieve a sample or estimate by eye.
How to find your soil texture
The quickest exact answer is the USDA Web Soil Survey: draw your area on the map and it lists each soil’s layers, textures and available water capacity. Without it, use the ribbon test: wet a walnut-sized ball of soil and push it out between thumb and finger. Gritty with no ribbon is sand; a short ribbon under 1 in is a loam family soil; 1 to 2 in is a clay loam; longer and sticky is clay. A jar test, shaking soil with water and letting it settle into sand, silt and clay bands, gives rough percentages.
How to read your result
| TAW | What it means | What to do |
|---|---|---|
| Under 1.0 in (25 mm) | A small reservoir. | Expect frequent watering, often daily for summer lawns. Deepen roots or add organic matter. |
| 1.0–3.0 in (25–76 mm) | Moderate storage. | Typical for lawns, beds and shallow crops. |
| Over 3.0 in (76 mm) | Large storage. | Deep, infrequent irrigation works well. |
| Rock over 35 % | Much less water stored. | Use shorter intervals. |
The RAW figure is how much to refill each time, before losses. Don’t apply more than the TAW at once: the extra drains below the roots.
How we build and check this calculator
Every default on this page is shown with its source, every value is editable, and the code is tested against worked cases before every update.
- Methods from recognised sources. The layer method and texture ranges follow the University of Nebraska–Lincoln Plant and Soil Sciences eLibrary and Nebraska Extension; TAW and RAW follow FAO-56; site values come from the USDA Web Soil Survey. See the sources.
- Tested against worked cases. Seven test cases run against the calculator code before every update, including the University of Nebraska “Soil A” profile (4.2 in in 5 ft), a profile cut at the root depth, rocky soil, lab values, a metric case and an impossible wilting point. All must match.
- Honest about limits. Texture averages can miss your soil by a quarter or more. Compaction, organic matter, salts and hardpans all change storage; a soil survey or lab test is the way to be sure.
- Your entries stay on your device. The calculator runs in your browser. Nothing you type is sent anywhere; your inputs live only in the page address, so you can bookmark or share a result.
- Corrections are welcome. If a number looks wrong, tell us. We check it against the sources, fix the page and update the date at the top.
Page history
- Published. Defaults, test cases and source links checked.
Questions
What is available water capacity?
It is the water a soil holds that plants can actually use, the amount between field capacity (what is left after the soil drains) and the wilting point (where roots can’t pull any more out). It is usually given in inches of water per foot of soil, or millimetres per metre.
Which soil holds the most water for plants?
Silt loams, at about 2.0 to 2.5 in per foot. Their many small pores hold a lot of water loosely enough for roots to take. Sands hold the least, under 1 in per foot, because their big pores drain. Clays hold plenty of water, but much of it is held too tightly for plants.
How do I find my soil’s texture and water capacity?
The USDA Web Soil Survey maps soils across the US and lists available water capacity by layer for your exact site. You can also judge texture by feel with the ribbon test or settle a soil sample in a jar of water to see the sand, silt and clay layers.
How do I calculate available water for a layered soil?
Multiply each layer’s thickness (in feet) by its water capacity (in inches per foot), stopping at the root depth, and add the layers up. A layer that runs past the roots only counts down to the root depth. The layered mode does this for up to four layers.
What is the difference between total and readily available water?
Total available water (TAW) is everything plants can extract between full and wilting. Readily available water (RAW) is the part they can use without stress, usually half of TAW. Irrigate when RAW is used up, and refill about that much each time.
How do rocks and gravel reduce water storage?
Stones take up space but hold no water for plants, so storage drops in proportion. Soil that is 20 % gravel by volume stores 20 % less. Above about 35 % the loss is large enough that you will need to water more often.
How much water should I apply to refill the root zone?
About the readily available water, plus extra for system losses. Applying more than the total available water just drains below the roots. The irrigation schedule calculator turns this storage into how often to water.
Sources
- University of Nebraska–Lincoln, Plant and Soil Sciences eLibrary, Soil Water (Tables 2.6 and 2.7). Available water capacity ranges by texture and the layered-profile method; our layered test reproduces its 4.2 in “Soil A” example.
- Nebraska Extension, Irrigation Scheduling Strategies When Using Soil Water Data (EC3036, S. R. Melvin and D. L. Martin, 2018). Single water-holding values by texture, including loam 2.0 and clay loam 1.8 in/ft.
- USDA Natural Resources Conservation Service, Web Soil Survey. Site-specific available water capacity by soil layer, the best value to type in for your own ground.
- Food and Agriculture Organization of the United Nations (FAO), Crop Evapotranspiration, Irrigation and Drainage Paper 56, Chapter 8: ETc under soil water stress conditions. TAW from field capacity and wilting point over the root depth, and RAW = p × TAW.
- South Dakota State University Extension, How Soil Holds Water. Inches of water in a foot of soil from field capacity and wilting point by volume.
- University of California Statewide IPM Program, Calculating available water-holding capacity of a soil profile (potato guidelines, figure 17). Layer-by-layer method with broader texture classes, showing how published values differ.
- USDA Natural Resources Conservation Service, National Engineering Handbook, Part 652: Irrigation Guide (via AgEcon Search). Basic intake rates by texture, shown next to the storage for cycle-and-soak planning.
- The rock correction (stones hold no plant-available water), the layer cut at the root depth and the volume conversions are derived on this page.
Links checked November 15, 2026. Texture values differ between sources and soils; the defaults are typical values, and you can type your own.