Irrigation Hydraulics Calculators
Every sprinkler and emitter depends on getting enough water at enough pressure. Measure what your supply gives, size pipe for the flow, add up the pressure lost on the way, and size a pump when the supply falls short.
Which calculator do you need?
- How many gallons per minute can my water supply give?Available Flow Rate (GPM) Calculator
- What pipe size do I need for this flow?Irrigation Pipe Size Calculator
- How much pressure do I lose in this pipe run or lateral?Irrigation Friction Loss Calculator
- How much pressure is left at the last head?Irrigation Pressure Calculator
- What total head and horsepower does my pump need?Irrigation Pump Calculator
All Hydraulics calculators
- Irrigation Friction Loss CalculatorPressure lost in a pipe run or a lateral with outlets.Open calculator →
- Irrigation Pipe Size CalculatorSmallest pipe size for a flow, by velocity and loss.Open calculator →
- Irrigation Pressure CalculatorPressure left at the last head, loss by loss.Open calculator →
- Irrigation Pump CalculatorTotal dynamic head and pump horsepower.Open calculator →
- Available Flow Rate (GPM) CalculatorSupply GPM from a bucket test or meter and service line.Open calculator →
The pressure budget
Think of pressure as a budget. Your supply starts with so many psi, and the meter, backflow preventer, valve, pipe and any climb uphill each spend some. What is left must still run the heads.
- Measure the supplyFind usable GPM, limited by the meter and service line, with the available flow calculator.
- Size the pipeKeep velocity at or under 5 ft/s with the pipe size calculator.
- Work out the lossFind pressure lost in pipe, fittings and laterals with the friction loss calculator.
- Check the last headAdd every loss and see what reaches the far end with the irrigation pressure calculator.
- Add a pump if neededFind total dynamic head and horsepower with the irrigation pump calculator.
- VelocityV (ft/s) = 0.4085 × GPM ÷ d² (d = inside diameter, inches)
- Friction (Hazen-Williams)psi per 100 ft = 0.2083 × (100 ÷ C)^1.852 × Q^1.852 ÷ d^4.8655 × 0.433
- Elevation0.433 psi per foot of rise; 1 psi lifts water 2.31 ft
- Water horsepowerWHP = GPM × TDH ÷ 3,960; brake hp = WHP ÷ pump efficiency
Friction grows roughly with the flow to the power 1.85, so doubling the flow nearly quadruples the loss.
Pipe size at a glance
| Nominal size | Sch 40 PVC or PE | Class 200 PVC |
|---|---|---|
| 3/4 in | 8.3 GPM | 10.6 GPM |
| 1 in | 13.5 GPM | 17.3 GPM |
| 1-1/4 in | 23.3 GPM | 27.6 GPM |
| 1-1/2 in | 31.7 GPM | 36.2 GPM |
| 2 in | 52.3 GPM | 56.5 GPM |
Class 200 PVC has a thinner wall, so its bore is wider at the same nominal size. Long runs may need one size up to keep pressure loss down even when velocity is fine.
Pressures heads need
| Emitter | Typical pressure |
|---|---|
| Fixed spray | about 30 psi |
| Rotary nozzle | about 40 psi |
| Rotor | about 45 psi |
| Drip (regulated) | often about 25 psi |
Static pressure is what a gauge reads with nothing flowing; sprinklers care about the dynamic pressure left while the zone runs. Pressure well above a head’s maximum makes it mist and drift, so a regulator can help. For farm systems, size the field flow with the system capacity calculator and price the energy with the pumping cost calculator.
Mistakes to avoid
Using static pressure
The gauge reading with taps closed overstates what the heads get. Plan from dynamic pressure.
Nominal size as the bore
1-in pipe isn’t 1 in inside. Friction and velocity use the inside diameter.
Forgetting the climb
A zone 20 ft up the slope loses about 8.7 psi before any friction.
Testing at the wrong tap
A hose bib may sit after a regulator or on smaller pipe. Test where the irrigation will connect.
How we build and check these calculators
- Methods from recognised sources. Hazen-Williams friction, university extension pump guides and published manufacturer engineering data, named on every calculator page.
- Tested before every update. Each calculator runs its worked cases in US and metric units before a change goes live.
- Open about method and limits. Read our editorial policy, or tell us if a number looks wrong.
Questions
What do GPM and PSI each tell me?
GPM is how much water flows, and it sets how many heads can run at once. PSI is how hard it pushes, and it sets whether those heads throw and spray properly. A system needs both.
How fast should water move in irrigation pipe?
About 5 ft/s or less in PVC. Faster water raises friction steeply and causes water hammer when valves close; many experts say never exceed 10 ft/s.
How much pressure loss is acceptable?
A common rule is no more than 20 % of the heads’ operating pressure across a zone, and many design guides aim for 10 %.
What pressure do sprinklers need?
Most spray heads work best around 30 psi at the nozzle, rotary nozzles around 40 psi and rotors around 45 psi. Drip usually runs lower through a regulator, often around 25 psi.
How do I measure my water supply’s flow?
Turn off all other water, open an outdoor tap fully and time a bucket of known size. GPM = gallons × 60 ÷ seconds. Then check the meter and service-line limits in the available flow calculator.
Do I need a booster pump?
Only if the pressure left at the heads falls short. Enter your city pressure as the pump’s inlet pressure; if it already meets the need at your flow, no booster is needed.
Sources
- Texas A&M AgriLife Extension (Fipps), Calculating Horsepower Requirements and Sizing Irrigation Supply Pipelines (EB-6011). Pipe sizing by velocity, total dynamic head and pump horsepower.
- Hunter Industries, Handbook of Technical Irrigation Information. Friction loss tables, pressure losses through components and head operating pressures.
- University of Florida IFAS Extension, Hydraulic Considerations for Citrus Microirrigation Systems (CH156). Hazen-Williams friction loss and the multiple-outlet lateral factor.
- Rain Bird Corporation, Irrigation Design Tip — Determining Water Supply Requirements. Meter and service-line limits for available flow.
- Kansas State University Research and Extension, Irrigation Formulas and Conversions (MF-2404). Pressure-head conversions and water horsepower.
Links checked November 16, 2026. Each calculator page lists its own full set of sources. Manufacturer documents are cited for their engineering data only; we have no ties to any manufacturer.