Available Flow Rate (GPM) Calculator

Work out the flow your water supply can deliver to a sprinkler system. Time a bucket at the tap, with any container size, or enter your meter and service line to apply the three supply limits and see which one governs. Then take the flow to the zone calculator.

Available flow calculator

Choose how to measure
Quick picks

1The test

gal
s

Faucet fully open, nothing else running. Time it twice.

psi

Note it: flow changes with pressure.

2Service line check (optional)

See your available flow ↓

How the calculator works

Before you plan zones, you need to know how much water your supply can give at once. There are two ways to find out.

  • Bucket testGPM = gallons × 60 ÷ seconds · L/min = litres × 60 ÷ seconds
  • Service-line velocityV (ft/s) = 0.4085 × GPM ÷ d² (d = inside diameter, inches)
  • Service-line limitGPM = Vlimit × d² ÷ 0.4085 (7.5 ft/s metal, 5 ft/s plastic)
  • Meter limit75 % of the meter’s maximum safe flow
  • Meter-loss limitthe flow where meter loss reaches 10 % of static (from the meter chart)
  • Available flowthe smallest of the limits

This page gives the flow your supply can carry. Apply a design margin and split it into zones with the sprinkler zone calculator.

Worked examples

A 5-gallon bucket

  1. Test5 gallons in 18 seconds.
  2. Result5 × 60 ÷ 18 = 16.67 GPM (63.1 L/min). 5 gallons in 30 s is 10.00 GPM; 2 gallons in 15 s is 8.00 GPM.

A 3/4-in meter with a 3/4-in copper line

  1. Service lineType K copper, ID 0.745 in, at 7.5 ft/s: 7.5 × 0.745² ÷ 0.4085 = 10.2 GPM.
  2. Meter75 % × 30 GPM = 22.5 GPM; meter-loss chart limit 24 GPM.
  3. Result10.2 GPM: the service line governs.

A 5/8-in meter with a 1-in PVC line

  1. LimitsService line at 5 ft/s: 13.5 GPM; meter: 75 % × 20 = 15.0 GPM.
  2. Result13.5 GPM, service line governs.

Bucket test chart (5-gallon bucket)

Seconds to fill 5 gallons and the flow.
SecondsGPML/min
10 s30.0113.6
15 s20.075.7
20 s15.056.8
30 s10.037.9
40 s7.528.4
50 s6.022.7
60 s5.018.9

Fills under 3 seconds are hard to time; use a larger container.

Meter and service line limits

Meter capacity at 75 % of maximum safe flow.
MeterMaximum safe flow75 % for irrigation
5/8 in20 GPM15.0 GPM
3/4 in30 GPM22.5 GPM
1 in50 GPM37.5 GPM
1-1/2 in100 GPM75.0 GPM
2 in160 GPM120.0 GPM

The service line, the pipe from the meter to the house, is often the real limit. A larger meter doesn’t help if the line is small. Size the irrigation main from this flow with the pipe size calculator.

If your flow is low

  • Use low-flow rotary nozzles or drip, which need far less per head.
  • Put fewer heads on each zone and run more zones.
  • For a well or pump, the pump curve sets the flow at your pressure; see the irrigation pump calculator.
  • Compare with what your heads use on the nozzle flow calculator.

Mistakes to avoid

Testing with water in use

A dishwasher or shower running during the test lowers the result. Test with everything off.

Designing to the bucket result alone

A strong tap can exceed the safe flow for the service line. Add the line check.

Using 100 % of the flow

Leave a margin, about 20 %, when you plan zones.

Guessing the bucket size

Many “5-gallon” buckets hold a little more or less. Mark a measured fill line.

How we build and check this calculator

Every rule on this page names its source, and the code is tested against worked cases before every update.

  • Methods from recognised sources. The three supply limits follow Rain Bird’s design method; the bucket test follows Hunter’s design guide. See the sources.
  • Tested against worked cases. Six cases run against the calculator code before every update: three bucket tests, the Rain Bird meter example, a 5/8-in meter with PVC, a metric test and a fill too fast to time. All must match.
  • Honest about limits. Local water suppliers may set their own limits; check with yours for larger systems.
  • Your entries stay on your device. The calculator runs in your browser. Nothing you type is sent anywhere; your inputs live only in the page address, so you can bookmark or share a result.
  • Corrections are welcome. If a number looks wrong, tell us. We check it against the sources, fix the page and update the date at the top.

Page history

Published. Methods, test cases and source links checked.

Questions

How do I do a bucket test for GPM?

Turn off all other water, open an outdoor tap fully, and time how long a bucket of known size takes to fill. GPM = gallons × 60 ÷ seconds; for a 5-gallon bucket that is 300 ÷ seconds.

How many GPM does a sprinkler system need?

It depends on the heads, not the yard. A zone of six sprays at 1.5 GPM uses 9 GPM; three rotors at 3 GPM use 9 GPM. Your supply sets the limit, and zones are sized to fit it.

What limits flow from the meter and service line?

Three rules apply. Flow through the meter should stay within 75 % of its maximum safe flow; the meter should lose no more than about 10 % of static pressure; and water in the service line should move no faster than 5–7.5 ft/s. The smallest wins.

Why can a hose bib test mislead?

A hose bib may sit on a smaller pipe or after a pressure regulator, and the result changes with pressure and time of day. Test at the point the irrigation will connect, when you plan to water, and check the service-line limit too.

GPM or PSI, which matters more?

Both. GPM sets how many heads can run at once; PSI sets whether they work properly. Measure flow here and check pressure with the irrigation pressure calculator.

What if my flow is low?

Use drip or low-flow rotary nozzles, put fewer heads on each zone, and run more zones. Under about 5 GPM, a drip-heavy design is often the best fit.

Sources

  1. Rain Bird Corporation, Irrigation Design Tip — Determining Water Supply Requirements. The three supply rules — meter loss no more than 10 % of static, flow no more than 75 % of the meter’s maximum safe flow (30 GPM for a 3/4-in meter), and service-line velocity 5–7.5 ft/s; worked example with a 3/4-in copper service line.
  2. Hunter Industries, Residential System Design Guide (LIT-226). The bucket test for available flow.
  3. Texas A&M AgriLife Extension (Fipps), Calculating Horsepower Requirements and Sizing Irrigation Supply Pipelines (EB-6011). Velocity from flow and inside diameter, and the 5 ft/s limit for plastic pipe.
  4. Maximum safe meter flows for other sizes (5/8 in 20, 1 in 50, 1-1/2 in 100, 2 in 160 GPM) follow AWWA displacement-meter capacities as used in design manuals. The bucket formula, service-line inside diameters (ASTM dimensions) and unit conversions are derived on this page.

Links checked November 15, 2026. The Rain Bird example (3/4-in meter, 3/4-in Type K copper) was reproduced at 10.2 GPM with the service line governing.