Irrigation Run Time Calculator

Find how many minutes to set each sprinkler or drip zone on your controller. The run time is adjusted for uneven coverage and split into cycles when your soil can’t soak the water up in one go.

Run time calculator

Choose your zone type
Quick picks
1What’s on the zone?

2Water and coverage

Enter the water need Required
in

Water the roots need each watering; lawns often take ½–¾ in. Not sure? Work out your plants’ water need.

in

Your weekly need. It is split evenly across the waterings below.

Watering days on the controller, 1–7. How many days?

in/hr

Set by the head type above; overwrite it with your measured rate. Measure it with a catch-cup test.

%

Lower-quarter DU from an audit. Leave it blank for no adjustment. Find your DU.

3Soil, for cycle & soak

Not sure? Do the ribbon test
  1. Wet a walnut-sized ball of soil until it feels like putty.
  2. Gritty and won’t hold a ball: sand or loamy sand.
  3. Push it out between thumb and finger. A ribbon under 1 in (2.5 cm) before it breaks: a loam family soil.
  4. A ribbon of 1–2 in: a clay loam family soil. Longer than 2 in and sticky: clay.
  5. Very gritty: pick the “sandy” version; smooth and floury: pick the “silty” one.

The list and the triangle set the same value.

in/hr

How fast water soaks in. Choose “Custom intake rate” to type your own.

Advanced: surface storage
in

Water that can sit on the surface before it runs off. 0.10 in is our assumption for turf on gentle slopes.

See your run time ↓

How the calculator works

Run time is the depth of water you want to apply divided by the rate your zone applies it, times 60. Half an inch from spray heads that apply 1.5 in/hr takes 20 minutes before any adjustment.

Two corrections turn that into a number you can trust on the controller. First, sprinklers never water evenly, so the run is stretched until the driest part of the zone gets enough. Second, if the heads put water down faster than your soil can take it in, the run is split into short cycles with a soak between them.

The three numbers that set run timeTwo sprinkler heads throw water across a lawn into catch cups that fill unevenly. Below the grass line, an arrow shows water soaking into the soil. 1 · Precipitation ratehow fast the heads put water down 2 · Uniformity (DU)driest cups against the average 3 · Soil intake ratehow fast water soaks in
Rate and uniformity come from the heads; intake comes from the soil. Run time needs the first two, and the cycle split needs the third.
  • Scheduling multiplierSM = 1 ÷ (0.4 + 0.6 × DU)
  • Gross depthgross depth = net depth × SM
  • Run time, minutesT = gross depth ÷ precipitation rate × 60, rounded up to a whole minute
  • Cycle and soaklongest cycle = surface storage ÷ (rate − intake rate) × 60 · soak = surface storage ÷ intake rate × 60
  • Drip, minutesT = gallons ÷ (emitters × GPH × efficiency) × 60

Why the run time is longer than depth ÷ rate

Distribution uniformity (DU) compares the driest quarter of a zone with its average. At DU 65 % the driest quarter catches only 65 % of the average, so the multiplier adds time: 1 ÷ (0.4 + 0.6 × 0.65) = 1.27, or 27 % more. The formula assumes the soil spreads some water sideways, so it adds less than a straight 1 ÷ DU would.

Scheduling multiplier at common DU values.
DU (lower quarter)MultiplierExtra run time
55 %1.37+37 %
65 %1.27+27 %
75 %1.18+18 %
85 %1.10+10 %

Better coverage is cheaper than more time. If your multiplier is above 1.30, fix the heads first; the distribution uniformity calculator finds your DU from a catch-cup test.

Units and conversions

Switch between inches and millimetres at the top of the calculator; the formulas don’t change. The constants are 1 in = 25.4 mm, 1 gal = 3.785 L, and 0.623 gal of water covers 1 sq ft to a depth of 1 in (7.48 gal per cubic foot ÷ 12). In metric, 1 mm over 1 m² is 1 L.

Controllers take whole minutes, so convert decimal hours by multiplying by 60 and rounding up: 1.75 hours is 105 minutes, and 0.4 hours is 24 minutes.

Worked examples

A lawn spray zone

  1. Inputs0.50 in per watering, precipitation rate 1.60 in/hr, DU 65 %, 3 waterings a week.
  2. Multiplier1 ÷ (0.4 + 0.6 × 0.65) = 1 ÷ 0.79 = 1.27.
  3. Gross depth0.50 × 1.27 = 0.63 in.
  4. Run time0.633 ÷ 1.60 × 60 = 23.7, rounded up to 24 minutes per watering, or 72 minutes a week.

The same zone on clay

  1. InputsAs above, 2 waterings a week, clay soil with an intake rate of 0.20 in/hr, surface storage 0.10 in.
  2. Longest cycle0.10 ÷ (1.60 − 0.20) × 60 = 4.3 minutes before water starts to run off.
  3. Cycles23.7 ÷ 4.3 = 5.5, so 6 cycles of 23.7 ÷ 6 = 4.0 → 4 minutes each.
  4. Soak0.10 ÷ 0.20 × 60 = 30 minutes between cycles. The zone still runs 24 minutes in total, 48 minutes a week.

How to read your result

Most residential sprinkler zones land between 3 and 60 minutes per watering. Where your result falls tells you what to do next.

Ranges for run time per watering and for the scheduling multiplier.
ResultWhat it meansWhat to do
Under 3 minVery short. Spray heads put water down fast, or the depth is small.Water fewer days with more time each, or check the precipitation rate.
3–60 minNormal for residential zones.Set it on the controller; use the cycle split if your soil needs it.
60–240 minLong, typical for rotors and low-rate nozzles.Use the cycle split if you see runoff.
Over 240 minUnusually long.Check the rate with a catch-cup test, or spread the water over more days.
Drip over 360 minA long drip set.Add emitters or use higher-flow emitters.
Multiplier ≤ 1.15Good uniformity.Nothing to fix.
Multiplier 1.16–1.30Fair uniformity.Adjusting heads or nozzles could cut run time.
Multiplier over 1.30Poor uniformity.Fix coverage before adding time.

How long to run sprinklers: run times by head type

Spray heads need about 20 minutes for half an inch; rotors need about an hour. The difference comes from the rate each head puts water down, not from how much water the lawn needs.

Typical rates; your nozzles may differ. “Typical DU” columns use the calculator’s default DU for each head type (spray 65 %, rotor 70 %, rotary 75 %, impact 70 %, hose-end 65 %).
Head typeTypical rate½ in, perfectly even½ in, typical DU1 in, typical DU
Spray heads1.5 in/hr20 min26 min51 min
Rotors0.5 in/hr60 min74 min147 min
Rotary nozzles0.4 in/hr75 min89 min177 min
Impact sprinkler0.4 in/hr75 min92 min183 min
Hose-end / oscillating0.3 in/hr100 min127 min254 min

These rates sit inside the ranges in manufacturers’ catalogues, but nozzle size, spacing and water pressure all change them. If your zone is far off these numbers, measure it with the precipitation rate calculator and enter the result as a measured rate.

Rotors and rotary nozzles run three to five times longer than sprays because they put water down three to five times more slowly. That slower rate is often an advantage on clay and slopes, because more of the water soaks in before it can run off.

Cycle and soak: stop runoff on clay and slopes

Cycle and soak splits one long run into several short ones with a rest between them, so each cycle soaks in before the next one starts. Use it whenever water puddles or runs onto the pavement before the zone finishes.

Runoff starts when the heads apply water faster than the soil takes it in and the small amount the surface can hold is used up. The calculator works out the longest cycle before that happens, how many cycles you need, and how long to soak so the surface drains. Program it as one run time per zone and a cycle and soak setting on the controller, or as several start times.

Mid-range basic intake rates by soil texture (USDA-NRCS guidance; slopes and compaction lower them). Longest cycle and soak assume spray heads at 1.5 in/hr and 0.10 in of surface storage.
SoilIntake rateLongest spray cycleSoak between cycles
Sand1.0 in/hr12.0 min6 min
Loamy sand0.8 in/hr8.6 min8 min
Sandy loam0.6 in/hr6.7 min10 min
Loam0.4 in/hr5.5 min15 min
Silt loam0.3 in/hr5.0 min20 min
Clay loam0.2 in/hr4.6 min30 min
Clay0.1 in/hr4.3 min60 min

The textures with “sandy” or “silty” in front of clay or clay loam on the calculator’s triangle use the clay or clay loam rate, and silt uses the silt loam rate. If you know your soil’s intake rate from a test, choose a custom intake rate and type it in.

How long to run drip irrigation for trees and beds

Drip run time is the water a plant needs divided by the flow of its emitters. A young tree that needs 12 gallons from four 1-GPH emitters runs about 3 hours 20 minutes at 90 % efficiency.

For a bed, the calculator first turns depth into gallons: half an inch over a 4 × 8 ft bed is 0.5 × 32 × 0.623 = 10.0 gallons. With sixty 1-GPH emitters and 90 % efficiency that takes 12 minutes.

The fastest way to shorten a long drip set is more flow at the plant: add emitters or swap to a larger size. The “What changes it most” panel under your result shows which change helps most for your layout. To size a new drip zone, use the drip irrigation calculator.

Tips and common mistakes

Water early in the morning

Less water is lost to wind and evaporation, and leaves dry off as the day warms.

Watch the first run

If you see puddles or water reaching the pavement, choose your soil above and use the cycle split.

Follow local watering rules

Never schedule beyond your water supplier’s watering days or hours, whatever the calculator says.

Don’t mix head types on one zone

Sprays and rotors on the same valve can’t both get the right water, because their rates differ several times over.

Re-run after nozzle changes

A new nozzle changes the precipitation rate, so the old run time no longer fits.

How we build and check this calculator

Every number on this page comes from a formula you can see and a source you can open, and the calculator is re-tested whenever the page changes.

  • Methods from recognised sources. The scheduling multiplier follows Irrigation Association auditor training and University of California Cooperative Extension material. Soil intake rates follow the USDA-NRCS Irrigation Guide. Head-type defaults sit inside published manufacturer ranges, and you can overwrite every one. See the sources.
  • Tested against worked cases. Seven test cases are run against the calculator code before every update: a spray lawn, a rotor zone with cycle and soak, spray heads on clay, a drip tree, a drip bed, a metric zone and a very low rate. All seven must match exactly. The two worked examples above are two of them.
  • Honest about limits. The result assumes one head type per zone, gentle slopes and established turf. For mixed zones, steep banks, heavily compacted soil or large commercial sites, an audit by an Irrigation Association Certified Landscape Irrigation Auditor will measure what this page can only estimate.
  • Your entries stay on your device. The calculator runs in your browser. Nothing you type is sent anywhere; your inputs live only in the page address, so you can bookmark or share a result if you choose.
  • Corrections are welcome. If a number looks wrong, tell us. We check it against the sources, fix the page and update the date at the top.

Page history

Published. Method, defaults, test cases and source links checked.

Questions

How many minutes should I water to put down 1 inch?

Divide 1 inch by your zone’s precipitation rate and multiply by 60, then add time for uneven coverage. Spray heads at 1.5 in/hr need 40 minutes before adjustment, or about 51 minutes at DU 65 %. Rotors at 0.5 in/hr need 120 minutes before adjustment. For half an inch, halve those times. Most lawns get their weekly inch over two or three waterings, not one.

How do I find my sprinkler’s precipitation rate?

Set out straight-sided cups across the zone, run it for a set time, and measure the average depth caught; that is the catch-cup test. The manufacturer’s nozzle chart gives a rate too, but it assumes ideal spacing and pressure. The precipitation rate calculator walks you through the test.

Why do rotors run so much longer than spray heads?

Rotors apply water about a third as fast as spray heads, so they need about three times as long to put down the same depth. They aren’t using more water. The slower rate lets more of it soak in, which is why rotors suit clay and slopes.

How do I convert decimal hours to controller minutes?

Multiply the hours by 60 and round up to a whole minute. 1.5 hours is 90 minutes, 1.75 hours is 105 minutes and 0.4 hours is 24 minutes. Many controllers cap a single run, so long rotor times may need two start times.

Should I change run times by season?

Usually the run time per watering stays about the same and the number of watering days changes, because hotter weather uses the same root-zone water faster. Many controllers also have a seasonal adjust percentage that scales every zone at once. The irrigation schedule calculator works out how many days a week to water.

Does the run time include the soak time?

No. The run time is the minutes the valve is open. Soak time is extra waiting between cycles, so a split program takes longer from start to finish but applies the same water. A 24-minute zone split into 6 cycles of 4 minutes with 30-minute soaks finishes about 2 hours 54 minutes after it starts.

How long should I run drip irrigation for a young tree?

Divide the gallons the tree needs by the total flow of its emitters, then allow for efficiency. Twelve gallons from four 1-GPH emitters at 90 % efficiency is 12 ÷ (4 × 1 × 0.9) × 60 = 200 minutes. Five gallons from the same emitters takes 84 minutes.

Sources

  1. Irrigation Association, Certified Landscape Irrigation Auditor (CLIA) program. The auditor training behind lower-quarter DU and the scheduling multiplier, 1 ÷ (0.4 + 0.6 × DU).
  2. University of California Cooperative Extension, Irrigation Scheduling: Determining Run Times (L. R. Oki, UC Davis). Works the same multiplier with DU 0.65 and uses depth ÷ precipitation rate × 60 for run time.
  3. University of California Cooperative Extension, Landscape Irrigation System Evaluation and Management (D. A. Shaw and D. R. Pittenger, 2009). Precipitation rate and distribution uniformity as the two system numbers that set station run times.
  4. USDA Natural Resources Conservation Service, National Engineering Handbook, Part 652: Irrigation Guide (via AgEcon Search). Soil intake rates by texture, the basis for the intake defaults and the cycle-and-soak check.
  5. USDA Natural Resources Conservation Service, Soil Texture Calculator. The USDA texture triangle used for the soil picker.
  6. Kansas State University Research and Extension, Estimating Soil Texture by Feel, MF2852 (D. Presley and S. Thien). The ribbon test summarised under the soil picker.
  7. Hunter Industries, Standard MP Rotator nozzle. Manufacturer data for rotary nozzles at about 0.4 in/hr, the rotary-nozzle default.
  8. Rain Bird, Landscape irrigation catalogue: rotors and spray nozzles. Published precipitation-rate ranges for rotors and sprays; the rotor and spray defaults sit inside them.
  9. Run time = depth ÷ application rate, the cycle-and-soak water balance and every unit conversion are derived on this page; nothing is hidden.

Links checked November 15, 2026. Manufacturer pages change often; if one moves, the rates quoted are typical values you can overwrite.

Related guides