Evapotranspiration (ET) Calculator

Find how much water a well-watered grass lawn loses to the air in a day, from whatever weather data you have. Pick high and low temperatures only, full weather station data, or a Class A pan reading, and get ETo per day, per week and for the month.

Evapotranspiration calculator

Choose the weather data you have
Quick picks

1Place and date

Hemisphere Required
°

Decimal degrees, 0–66.5. Any map app shows it when you press on your location.

The date sets the sun’s angle and the day length.

2Temperatures

°F

The day’s high, measured in the shade.

°F

The day’s low, usually just before sunrise.

See your ETo ↓

How the calculator works

Reference evapotranspiration (ETo, also written ET0 or called reference ET) is the water a large field of short, well-watered grass loses in a day. Sun, heat, dry air and wind drive it. This calculator estimates it from the weather data you have.

Every irrigation plan starts here. ETo says how thirsty the weather is; a plant coefficient then says how much of that a lawn, tree or crop actually uses. The calculator gives you the daily value plus weekly and monthly totals, so you can plan a schedule or a season.

What drives evapotranspirationThe sun heats a grass surface. Dry air and wind carry water vapor away from the leaves and soil. Below the grass line, the root zone supplies the water. Sunenergy to evaporate water Dry airpulls vapor off the leaves Windcarries moist air away Root zone supplies the water
ETo combines all four: energy from the sun and heat, the air’s dryness, wind, and a grass surface that never runs short of water.

The calculator offers three methods, one for each kind of data:

  • Hargreaves, temperature onlyETo = 0.0023 × (Tmean + 17.8) × √(Tmax − Tmin) × 0.408 × Ra, temperatures in °C, result in mm/day
  • FAO-56 Penman-MonteithETo = [0.408 Δ (Rn − G) + γ (900 ÷ (T + 273)) u₂ (es − ea)] ÷ [Δ + γ (1 + 0.34 u₂)], with G = 0 for a daily step
  • Class A panETo = Kp × pan evaporation
  • Extraterrestrial radiationRa from latitude and day of the year, using the solar constant 0.0820 MJ/m²/min
  • Totalsper week = daily ETo × 7; for the month = daily ETo × days in the chosen month

Ra is the sunshine that reaches the top of the atmosphere. It depends only on where you are and the date, which is why the first two methods ask for latitude and a date. The date also sets the day length shown in the drawing under your result.

Missing weather data

Penman-Monteith works with partial data, using the FAO-56 fallbacks. With no humidity, the dew point is taken as the day’s low temperature. With no wind, 2.0 m/s (4.5 mph) is used. With no radiation reading, sunshine is estimated from the temperature range, with a factor of 0.16 inland or 0.19 near the coast. Wind measured above 6.6 ft (2 m) is converted down to 2 m: u₂ = u × 4.87 ÷ ln(67.8 h − 5.42), with h in metres.

Converting mm per day to inches per day

Switch between °F · in and °C · mm at the top of the calculator; every field converts. The constants are 1 in = 25.4 mm, °C = (°F − 32) × 5 ÷ 9, 1 mph = 0.447 m/s and 1 ft = 0.3048 m. So 6 mm/day is 0.24 in/day, and 0.30 in/day is 7.6 mm/day.

Penman-Monteith vs Hargreaves vs pan: which to use

Use the method that matches your data. Penman-Monteith is the standard; Hargreaves and the pan are good fallbacks when data is missing.

The three methods compared.
MethodData neededBest forWatch out for
FAO-56 Penman-MonteithHigh and low temperature, elevation; humidity, wind and sunshine if you have themAny weather station; the international and US standardNeeds the most data; bad sensor data gives bad ETo
HargreavesHigh and low temperature, latitude, dateLong-term planning, places with only temperature recordsReads high in humid, calm places and low in windy, dry ones
Class A panOne day’s pan evaporation and a pan coefficientFarms and stations that keep a panThe pan coefficient is a judgment call; a poorly sited pan misleads

In the US the ASCE-EWRI standardized reference ET equation is the official version of Penman-Monteith. For daily grass reference ET it gives values very close to FAO-56, which is what this calculator uses. Blaney-Criddle, an older temperature method, is not offered because Hargreaves does the same job with fewer assumptions.

Worked examples

Hargreaves on a hot inland day

  1. InputsLatitude 36° N, July 15 (day 196), high 95 °F (35.0 °C), low 65 °F (18.3 °C).
  2. SunFor that latitude and date Ra = 40.8 MJ/m²/day, with 14.2 hours of daylight.
  3. TemperaturesTmean = (35.0 + 18.3) ÷ 2 = 26.7 °C; the range is 16.7 °C.
  4. ETo0.0023 × (26.7 + 17.8) × √16.7 × 0.408 × 40.8 = 6.95 mm/day = 0.27 in/day, or 1.92 in a week and 8.48 in for July.

Penman-Monteith: the FAO-56 check

  1. InputsBrussels, 50.8° N, July 6 (day 187), elevation 100 m, 21.5 °C high and 12.3 °C low, humidity 84 % and 63 %, wind 10 km/h measured at 10 m, 9.25 hours of sunshine.
  2. Wind2.78 m/s at 10 m becomes 2.08 m/s at 2 m.
  3. RadiationRs = 22.07 MJ/m²/day from sunshine hours; net radiation Rn = 13.28 MJ/m²/day.
  4. EToThe equation gives 3.88 mm/day, which matches the published FAO-56 answer of 3.9 mm/day. The “Solved with your numbers” panel shows every step when you enter this day.

A Class A pan reading

  1. InputsPan evaporation 0.35 in in one day, pan coefficient 0.70.
  2. ETo0.70 × 0.35 = 0.245, shown as 0.25 in/day (6.2 mm/day).

How to read your result

The calculator labels each result with a demand band. The band tells you how hard the weather is pulling on the soil and what it means for watering.

Daily ETo bands used in the result.
ETo per dayDemandWhat it means
Under 0.10 in (2.5 mm)LowCool or cloudy weather; irrigation needs are small.
0.10–0.20 in (2.5–5 mm)ModerateTypical of spring, fall or a mild summer day.
0.20–0.30 in (5–7.6 mm)HighTypical of summer; plan peak-season schedules from this range.
Over 0.30 in (7.6 mm)Very highHot, dry and windy; check that your system can keep up.
Over 0.50 in (12.7 mm)Check inputsOutside normal daily values; a temperature, humidity or wind entry is probably wrong.

ETo is for grass that never runs short of water. To get your plants’ need, multiply by a coefficient in the water requirement calculator. To decide how many days apart to water, take that daily use to the irrigation schedule calculator.

Typical ETo values by season and climate

Summer ETo in the US runs from about 0.15 in/day on a cool coast to 0.30 in/day and more in the low desert. Use these ranges as a sanity check, not as a replacement for local data.

Approximate peak-month ETo by US climate type. California rows follow UC and CIMIS averages; the humid and cool-summer rows convert the FAO-56 regional ranges. Local values vary; use your nearest ET station when you can.
Climate typePeak month, in/dayPeak month, mm/dayExample
Cool coastal, marine layer0.15–0.204–5Coastal California
Inland valley0.25–0.326–8California’s Central Valley
Low desert0.30–0.35+7.6–9+Imperial Valley, Phoenix area
Humid, warm summer0.16–0.284–7The Southeast and Gulf Coast
Cool, humid summer0.08–0.162–4The upper Midwest and Northeast in a mild spell

Spring and fall ETo is usually a third to a half of the summer peak, because the sun is lower and the days are shorter. At 40° N, Ra falls from 40.8 MJ/m²/day in mid-July to 22.5 in mid-October and 15.0 in mid-January. Winter ETo in cool climates is often under 0.05 in/day.

Where to get ETo data instead of calculating it

Many states run ET networks: weather stations over grass that publish daily ETo. California has CIMIS, Texas has the TexasET Network, and Florida has FAWN; many land-grant universities run their own. These values come from good sensors and a standard equation, so use them directly in the water requirement calculator when a station is near you.

Check two things before you use a network value. First, is it ETo (grass) or ETr (alfalfa)? ETr runs 15 to 35 % higher. Second, is it today’s value or a long-term average? Averages are fine for planning a season, but a hot, windy week can run well above them.

ETo vs ETr

ETo uses short grass, about 4 to 6 in (0.12 m) tall, as the reference. ETr uses alfalfa, about 20 in (0.5 m) tall, which is rougher and loses more water. Crop coefficients are written for one or the other, so match them: a coefficient for ETr used with ETo will under-water.

Pan evaporation and the pan coefficient

A Class A pan is a round, open pan of water 4 ft (1.21 m) across. The water it loses in a day is more than a grass field loses, because the pan is open water that heats up and has no leaves to close their pores. The pan coefficient Kp scales it down.

Kp runs from about 0.35 to 0.85. It is higher when the pan sits in a large green field and the air is humid and calm, and lower when the pan sits on bare, dry ground in a windy, dry place. 0.70 is a common middle value; adjust it if you know your pan’s setting.

Tips and common mistakes

Don’t confuse ETo with plant need

ETo is for reference grass. A shrub bed may use half of it and a tomato at peak more than all of it.

Check the weather station

A thermometer on a hot roof or pavement reads high and inflates ETo. Station data measured over grass is best.

Enter the wind height

Airport wind is often measured at 33 ft (10 m). Enter that height so the calculator converts it to 2 m.

Plan with averages, schedule with today

Long-term averages size a system; daily ETo, or last week’s total, sets this week’s watering.

Subtract rain separately

ETo ignores rain. Credit the rain that actually reaches the roots with the effective rainfall calculator.

How we build and check this calculator

Every equation on this page comes from FAO Irrigation and Drainage Paper 56 or the original Hargreaves paper, and the code is tested against worked cases before every update.

  • Methods from recognised sources. Penman-Monteith, the radiation terms, the missing-data steps and the pan method follow FAO-56. The temperature method follows Hargreaves and Samani (1985). Typical values come from FAO-56 and University of California guidance. See the sources.
  • Tested against worked cases. Seven test cases run against the calculator code before every update, including the FAO-56 Brussels example (3.88 mm/day against the published 3.9), a hot inland day, a spring day, a measured-radiation day, a pan reading and a zero-range day. All must match.
  • Honest about limits. One day of weather gives one day of ETo. Readings from poorly sited sensors, very high elevations or the polar regions (above 66.5°) are outside what this page can check.
  • Your entries stay on your device. The calculator runs in your browser. Nothing you type is sent anywhere; your inputs live only in the page address, so you can bookmark or share a result.
  • Corrections are welcome. If a number looks wrong, tell us. We check it against the sources, fix the page and update the date at the top.

Page history

Published. Methods, test cases and source links checked.

Questions

What is reference evapotranspiration (ETo)?

ETo is the water a large field of short, healthy, well-watered grass loses in a day through evaporation from the soil and transpiration from the leaves. It measures how thirsty the weather is. It is not the water your own plants use; you multiply ETo by a crop or plant coefficient to get that.

Which method should I use, Penman-Monteith or Hargreaves?

Use Penman-Monteith whenever you have humidity or wind data; it is the international standard. Use Hargreaves when you only have high and low temperatures. Hargreaves can’t see humidity or wind, so it tends to read high in humid, calm places and low in dry, windy ones.

What is a normal ETo in summer?

In most of the US, summer ETo runs about 0.15 to 0.30 in/day (4 to 7.5 mm/day). Cool coastal places stay near the low end, inland valleys reach about 0.30, and low deserts often go higher. Spring and fall values are usually half the summer peak or less.

How do I convert mm per day to inches per day?

Divide millimetres by 25.4. 5 mm/day is 0.20 in/day and 7.6 mm/day is 0.30 in/day. To go the other way, multiply inches by 25.4.

What is the difference between ETo and ETr?

ETo uses short grass as the reference surface; ETr uses taller alfalfa, which loses more water, so ETr is usually 15 to 35 % higher on the same day. This calculator gives ETo. If your weather network reports ETr, use crop coefficients written for ETr with it.

How do I turn ETo into how much water my lawn or garden needs?

Multiply ETo by a coefficient for your plants, about 0.8 for cool-season grass and 0.6 for warm-season grass, or a crop coefficient by growth stage. The water requirement calculator does this and gives gallons too.

Why does wind and low humidity raise ET so much?

Dry air pulls water vapor away from leaves faster, and wind keeps replacing the moist air next to the leaves with drier air. On a hot, dry, windy day ETo can be twice what it is on a hot, humid, still day with the same sunshine.

Sources

  1. Food and Agriculture Organization of the United Nations (FAO), Crop Evapotranspiration, Irrigation and Drainage Paper 56, Chapter 3: Meteorological data (Allen, Pereira, Raes and Smith, 1998). Extraterrestrial radiation, the solar constant, missing humidity and radiation procedures, the kRs values 0.16 inland and 0.19 coastal, and the wind height conversion used here.
  2. Food and Agriculture Organization of the United Nations (FAO), Crop Evapotranspiration, Irrigation and Drainage Paper 56, Chapter 1: Introduction to evapotranspiration. Defines reference ET and gives the typical ETo ranges by climate region behind the typical-values table.
  3. American Society of Agricultural and Biological Engineers, Reference Crop Evapotranspiration from Temperature (G. H. Hargreaves and Z. A. Samani, Applied Engineering in Agriculture, 1985). The temperature-only equation used in the Hargreaves mode.
  4. University of California, Davis, Biometeorology Program, Penman-Monteith reference evapotranspiration and Hargreaves-Samani steps (ASCE-EWRI standardized equation). Step-by-step ETo for the ASCE-EWRI standardized short reference, the US equivalent of FAO-56, and the 0.408 conversion in Hargreaves.
  5. University of California Center for Landscape and Urban Horticulture, ET: Evapotranspiration and Plant Water Use. Typical daily ETo for coastal, inland and desert locations and how real-time ETo differs from long-term averages.
  6. California Department of Water Resources, California Irrigation Management Information System (CIMIS). A public ET network that reports daily ETo in inches; one of the places to get ETo instead of calculating it.
  7. University of Florida IFAS Extension, Evapotranspiration-Based Irrigation for Agriculture: Sources of Evapotranspiration Data for Irrigation Scheduling in Florida (AE455). How to get daily and historical ETo from the Florida Automated Weather Network (FAWN).
  8. Unit conversions (°F to °C, mph to m/s, feet to metres, mm to inches) and the weekly and monthly totals are derived on this page.

Links checked November 15, 2026. The calculator follows the FAO-56 coefficients; the ASCE-EWRI standardized equation gives values very close to FAO-56 for daily grass reference ET.