Water Needs Calculators

Work out how much water your plants actually use, how much your soil can hold, how much rain counts, and then turn that into watering days and controller run times. Six calculators that follow the same path a landscape auditor or farm advisor uses.

Which calculator do you need?

All Water Needs calculators

From weather to run time

Watering well comes down to three questions: how much water the plants used, how much the soil can hold, and how long your system takes to put it back. These calculators answer them in order.

  1. Find the demandGet daily reference ET from your temperatures or a weather station with the ET calculator.
  2. Adjust it for your plantsTurn ET into the depth or gallons your lawn, shrubs, trees or crop need with the water requirement calculator.
  3. Take off the rainCount only the rain that soaks into the root zone with the effective rainfall calculator.
  4. Size the reservoirFind how much water your root zone stores with the available water capacity calculator.
  5. Space the wateringsFind the days between waterings, or how many days a week, with the irrigation schedule calculator.
  6. Set the controllerTurn the depth into minutes per zone, with cycle and soak if needed, using the irrigation run time calculator.

Each step’s result is a starting value for the next, so you can stop wherever you already have a number. Most people come back to the run time calculator a few times a year as the weather changes.

Numbers worth knowing

Daily reference ET bands used in the ET calculator.
Daily EToDemandTypical of
Under 0.10 in (2.5 mm)LowCool or cloudy weather
0.10–0.20 in (2.5–5 mm)ModerateSpring, fall or a mild summer day
0.20–0.30 in (5–7.6 mm)HighSummer; plan peak schedules from here
Over 0.30 in (7.6 mm)Very highHot, dry and windy days
Distribution uniformity and how much extra run time it adds.
Lower-quarter DUScheduling multiplierExtra run time
85 %1.10+10 %
75 %1.18+18 %
65 %1.27+27 %
55 %1.37+37 %

One inch of water over one square foot is 0.623 gallons, so an inch on a 1,000 sq ft lawn is about 623 gallons. Measure your own DU with the distribution uniformity calculator and your zone’s rate with the precipitation rate calculator.

How soil changes the schedule

Water held per foot of soil and typical intake rate (University of Nebraska–Lincoln values used in the calculators).
TextureWater held, in/ftIntake, in/hrWhat it means
Sand0.751.0Small reservoir; water often, in short runs
Sandy loam1.300.6Moderate storage
Loam2.000.4Good storage; longer intervals
Silt loam2.250.3Holds a lot; soaks in slowly
Clay loam1.800.2Slow intake; use cycle and soak

Spray heads put down 1–2 inches an hour, far faster than clay can take in 0.2 in/hr. That is why the run time calculator splits long runs into cycles with soak time between them.

Mistakes to avoid

One schedule all year

A hot summer day can pull two to three times the water of a mild spring day. Recheck run times as the seasons change.

Same minutes for every zone

Spray zones and rotor zones put water down at very different rates. Each zone needs its own run time.

Counting all the rain

Light showers mostly evaporate and heavy storms run off. Only effective rain refills the root zone.

Watering past the roots

Water that soaks below the roots is wasted. Size each watering to what the root zone can hold.

How we build and check these calculators

  • Methods from recognised sources. FAO-56, University of California, University of Nebraska and Irrigation Association methods, named on every calculator page.
  • Tested before every update. Each calculator runs its worked cases in US and metric units before a change goes live.
  • Open about method and limits. Read our editorial policy, or tell us if a number looks wrong.

Questions

How much water does a lawn need per week?

It depends on the weather and the grass. A lawn uses about the reference ET times its crop coefficient, which in summer often works out to about 1 to 1.5 inches a week, rain included. Use the ET and water requirement calculators to get the figure for your area.

Which calculator should I start with?

If you don’t know how much water your plants use, start with the ET calculator, then the water requirement calculator. If you already know the depth you want to apply, go straight to the run time calculator.

What is ET?

Evapotranspiration is the water that leaves the ground by evaporation and through plant leaves. Reference ET (ETo) is that loss from a standard grass surface, and every plant’s need is worked out from it.

Why does soil type matter for watering?

Soil is the reservoir. Sand holds about 0.75 in of water per foot of depth and loam about 2 in, so a sandy lawn needs water more often in smaller amounts, while loam can go longer between deeper waterings.

Should I water every day?

Usually not. Deep, less frequent watering that refills the root zone grows deeper roots. The schedule calculator finds how long your soil and plants can go between waterings.

Do these calculators follow local watering rules?

No. They work out what the plants need. Always follow your water supplier’s watering days and any drought restrictions.

Sources

  1. Food and Agriculture Organization of the United Nations (FAO), Crop Evapotranspiration, Irrigation and Drainage Paper 56, Chapter 1. The reference ET concept and crop coefficients used across these calculators.
  2. University of California Center for Landscape and Urban Horticulture, ET — Evapotranspiration and Plant Water Use. How landscape water needs are worked out from reference ET.
  3. University of Nebraska–Lincoln, Plant and Soil Sciences eLibrary, Soil Water (available water capacity by texture). Water held per foot of soil for each texture, used in the soil-storage table.
  4. Irrigation Association, Using Distribution Uniformity to Evaluate the Quality of a Sprinkler System. Distribution uniformity and the scheduling multiplier behind run times.

Links checked November 16, 2026. Each calculator page lists its own full set of sources.