Drip Irrigation Calculators
Plan a drip zone from the plant up. Count emitters and zone flow, check how long a row can run before the far end goes short, see how pressure changes emitter flow, and space emitters so their wet spots meet in your soil.
Which calculator do you need?
- How many emitters, how much tubing and how much flow does my drip zone need?Drip Irrigation Calculator
- How far apart should emitters be in my soil?Drip Emitter Spacing Calculator
- How long can one dripline or tape row run from a single inlet?Drip Line Length Calculator
- What does an emitter flow at my pressure, and how even is my block?Drip Emitter Flow Calculator
All Drip calculators
- Drip Irrigation CalculatorEmitters, dripline, zone flow and zones for any drip layout.Open calculator →
- Drip Line Length CalculatorLongest dripline or tape row one inlet should feed.Open calculator →
- Drip Emitter Flow CalculatorEmitter flow at pressure, exponent and field EU test.Open calculator →
- Drip Emitter Spacing CalculatorEmitter spacing, emitters per plant and percent wetted.Open calculator →
Planning a drip zone
Drip waters the root zone, not the whole yard, so the plan starts with the plants and the soil and ends with the supply.
- Space the emittersFind a spacing whose wet spots meet in your soil, and the emitters each plant needs, with the emitter spacing calculator.
- Count and add up the flowGet emitter count, dripline footage, zone flow and zones with the drip irrigation calculator.
- Check the longest rowMake sure the far end gets enough pressure with the drip line length calculator.
- Check the emitters in the fieldAdjust flow to your real pressure, or test a block’s uniformity, with the emitter flow calculator.
- Set the run timeUse the drip mode of the run time calculator, starting from the plants’ daily need in the water requirement calculator.
- Zone flowGPM = emitters × GPH per emitter ÷ 60
- Application ratein/hr = 231 × GPH ÷ (emitter spacing × row spacing, inches)
- Emitter lawq = k × P^x (x ≈ 0.5 for turbulent emitters, near 0 for pressure-compensating)
- Wetted radiusr (in) ≈ 8.57 × √(GPH ÷ soil intake in/hr)
Emitter spacing by soil
| Soil (intake) | 0.5 GPH | 1.0 GPH | 2.0 GPH |
|---|---|---|---|
| Sand (1.0 in/hr) | 11.5 | 16.3 | 23.0 |
| Sandy loam (0.6 in/hr) | 14.9 | 21.0 | 29.7 |
| Loam (0.4 in/hr) | 18.2 | 25.7 | 36.4 |
| Clay loam (0.2 in/hr) | 25.7 | 36.4 | 51.5 |
| Clay (0.1 in/hr) | 36.4 | 51.5 | 72.8 |
Water drops straight down through sand, so emitters go closer together. In clay it spreads sideways, so they can sit further apart. Measure a real wet spot if you can: run one emitter for an hour or two and dig across it.
Pressure, row length and uniformity
Friction takes pressure away along every row, and each foot of rise costs another 0.433 psi. Non-compensating emitters give less water as pressure falls, so long or uphill rows water unevenly. Manufacturers treat 10 % flow variation along a row as uniform and 10–20 % as acceptable.
Feeding a row from the middle makes two shorter laterals and roughly doubles the usable length. For pipe sizing to the zone, see the friction loss calculator. For fertilizer through drip, see the fertigation calculator.
Mistakes to avoid
Comparing GPH to GPM
Emitters are rated per hour and supplies per minute. Divide GPH by 60 before you compare.
Drip on a sprinkler zone
Drip needs low pressure, filtering and its own valve. Never share a zone with sprinklers.
Bigger emitters for big plants
A larger emitter mostly drives water deeper. Add emitters to spread water across the root zone.
Emitters at the trunk
Established trees take up water near the canopy edge. Move emitters out as the tree grows.
How we build and check these calculators
- Methods from recognised sources. B.C. Trickle Irrigation Manual equations, university extension guides and Irrigation Association papers, named on every calculator page.
- Tested before every update. Each calculator runs its worked cases in US and metric units before a change goes live.
- Open about method and limits. Read our editorial policy, or tell us if a number looks wrong.
Questions
How do I plan a drip zone?
Start with the plants. Space emitters for your soil, count them, add up the flow in gallons per hour, then divide by 60 to compare with your supply in GPM. Check row length last so the far end gets enough water.
How many drip emitters can I put on one zone?
Divide the flow you can use by the flow of one emitter. With 8 GPM available and an 80 % margin, a zone can run 6.4 × 60 = 384 one-GPH emitters.
How far apart should drip emitters be?
Far enough that their wet circles just overlap. With 1 GPH emitters that is about 16–18 in in sand, about 24 in in loam, and 48 in or more in clay.
Should I use pressure-compensating emitters?
On long rows, slopes and uneven ground, yes; they keep the same flow across a wide pressure range. Non-compensating emitters cost less and suit short, level runs.
How long does drip need to run?
Longer than sprinklers, because drip applies water slowly. The run time calculator has a drip mode that works from gallons per plant, emitter count and emitter flow.
What is emission uniformity?
How evenly a block’s emitters flow, from catch readings. 90 % or more is excellent and 80–89 % good; lower usually means clogging or pressure differences.
Sources
- B.C. Ministry of Agriculture and Food, B.C. Trickle Irrigation Manual (1999), Appendix E — Equations. Emitter flow, application rate and lateral friction equations.
- Oklahoma State University Extension, Drip Irrigation Systems (BAE-1511). Drip system parts, layout and zone planning.
- Irrigation Association (Lamm and Rogers, Kansas State University), Hydraulic Considerations for SDI Systems. Emitter exponents, flow variation and lateral length.
- Irrigation Association (von Bernuth and Mecham), Drip System Design for Established Landscape Trees and Shrubs. Wetted area, emitter spacing and emitters per plant.
Links checked November 16, 2026. Each calculator page lists its own full set of sources.