Drip Emitter Flow Calculator

See what a drip emitter actually delivers at your pressure from its rated flow, find its pressure exponent from two measured readings, or run a field test with catch volumes and get the emission uniformity, coefficient of variation and flow variation, with what to do if the zone is clogging.

Drip emitter flow calculator

Choose what you know
Quick picks

1First reading

Solve for Required
GPH
psi

Spec sheet in metres of head? Divide by 10.2 for bar.

2New pressure or second reading

psi
GPH
psi
See the emitter flow ↓

How the calculator works

Every emitter follows a simple law: flow equals a constant times pressure raised to a power, q = k × P^x. Knowing x tells you how the emitter reacts when pressure changes.

  • Flow at a new pressureQ₂ = Q₁ × (P₂ ÷ P₁)^x (any pressure unit, as long as both match)
  • Exponent from two readingsx = log(Q₁ ÷ Q₂) ÷ log(P₁ ÷ P₂)
  • Catch to flowGPH = mL ÷ 3,785.41 ÷ (minutes ÷ 60) · L/h = mL ÷ 1,000 ÷ (minutes ÷ 60)
  • Field EUaverage of the lowest quarter of flows ÷ average of all × 100
  • SpreadCV = standard deviation ÷ mean · flow variation = (max − min) ÷ max × 100
  • Design EU[1 − 1.27 × CVmaker ÷ √n] × (qmin ÷ qavg) × 100, n = emitters per plant

Worked examples

A non-PC emitter at higher pressure

  1. Rating1.0 GPH at 15 psi, exponent 0.50; running at 25 psi.
  2. Result1.0 × (25 ÷ 15)^0.5 = 1.29 GPH, +29.1 %. A PC emitter (x = 0.03) gives 1.015 GPH, +1.5 %.

Exponent from two readings

  1. Readings0.95 GPH at 10 psi and 1.25 GPH at 20 psi.
  2. Resultx = log(0.95 ÷ 1.25) ÷ log(10 ÷ 20) = 0.396, typical of a vortex or turbulent non-PC emitter.

A field test that shows clogging

  1. Catches60, 40, 58, 35, 62, 45, 30, 59 mL in 1 minute; maker’s CV 0.05, 2 emitters per plant.
  2. FlowsAverage 0.771 GPH; lowest 0.476 GPH; lowest two average 0.515 GPH.
  3. ResultEU = 0.515 ÷ 0.771 = 66.8 % (poor); CV 0.261; variation 51.6 % (unacceptable); design EU 58.9 %.

Metric check against a published dripper

  1. Rating1.60 L/h at 10 m of head (about 1 bar), x = 0.45.
  2. ResultAt 15 m: 1.60 × 1.5^0.45 = 1.92 L/h, matching the maker’s K and x.

Emitter exponents explained

Typical exponents and what 20 % more pressure does to flow.
Emitter typeExponent xFlow at +20 % pressure
Pressure-compensating0–0.1+0 to +1.8 %
Vortexabout 0.4+7.6 %
Turbulent (labyrinth)about 0.5+9.5 %
Laminar / microtube0.7–1.0+13.6 to +20 %

A lower exponent means less sensitivity to pressure, which allows longer rows and steeper ground. The exponent feeds straight into the drip line length calculator.

How to run a field flow test

  1. Pick emittersChoose 16 or more spread across the block: near the inlet, the middle and the far ends of several rows.
  2. RunLet the zone fill and reach normal pressure.
  3. CatchHold a cup under each emitter for exactly the same time, such as one minute.
  4. MeasureRead each catch in millilitres; enter 0 for an emitter that gives nothing.

Add the rated flow to see whether the block is under-delivering, and the maker’s CV with emitters per plant for a design EU.

Reading the results

Field emission uniformity and flow variation ratings.
ResultRatingWhat to do
EU 90 % or moreExcellentKeep the maintenance routine.
EU 80–89 %GoodCheck filters and flush at the next service.
EU 70–79 %FairFlush laterals and clean filters now.
EU under 70 %PoorFlush, clean, check for clogging and pressure differences.
Variation over 20 %UnacceptableFind and fix the low emitters or the low-pressure rows.
Average under 90 % of ratedUnder-deliveringLow pressure, clogging or worn emitters.

For sprinkler zones, the equivalent test is distribution uniformity with catch cups.

Clogged emitters and fixes

  • Flush the ends of the laterals until the water runs clear.
  • Clean or replace the filter screen or disc; drip usually needs 120–150 mesh.
  • Check pressure at the far end of the zone; low pressure looks like clogging on non-PC emitters.
  • For mineral or algae build-up, follow the product’s guidance on chlorine or acid treatment.

Mistakes to avoid

Mixing pressure units in K

A K given with pressure in metres gives the wrong flow with bar. Use the rated-flow route instead.

Testing only near the valve

The emitters nearest the inlet run at the highest pressure. Include the far ends of the rows.

Using the PC exponent below range

Below its minimum pressure a PC emitter behaves like a non-PC one.

Uneven catch times

A few seconds’ difference changes the flow. Time each catch the same, or catch for longer.

How we build and check this calculator

Every formula on this page names its source, and the code is tested against worked cases before every update.

  • Methods from recognised sources. The emitter law, exponent and design EU follow the B.C. Trickle Irrigation Manual and ISO-based manufacturer data; flow variation bands follow an Irrigation Association paper. See the sources.
  • Tested against worked cases. Seven cases run against the calculator code before every update: non-PC and PC emitters at a new pressure, an exponent from two readings, a healthy and a clogging field test, a published metric dripper, and equal pressures. All must match.
  • Honest about limits. One test is one moment. Pressure, temperature and clogging change over a season; retest after maintenance.
  • Your entries stay on your device. The calculator runs in your browser. Nothing you type is sent anywhere; your inputs live only in the page address, so you can bookmark or share a result.
  • Corrections are welcome. If a number looks wrong, tell us. We check it against the sources, fix the page and update the date at the top.

Page history

Published. Methods, test cases and source links checked.

Questions

How does pressure change drip emitter flow?

It depends on the emitter’s exponent x in q = k × P^x. A turbulent non-PC emitter (x ≈ 0.5) gives about 10 % more water for 20 % more pressure. A pressure-compensating emitter (x near 0) barely changes inside its working range.

What is the emitter exponent?

It measures how sensitive an emitter is to pressure. 0 means fully compensating, 0.5 is a typical turbulent emitter, and 1 means flow rises in step with pressure, as in laminar microtube. Manufacturers working to ISO 9261 must declare it.

How do I test drip emitter output in the field?

Run the zone at normal pressure, hold a measuring cup under each of 16 or more emitters spread across the block for one minute, and note the millilitres. Enter them with the catch time; 63 mL in one minute is 1.0 GPH.

What is a good emission uniformity for drip?

90 % or more is excellent and 80–89 % good. Below 70 % the block is uneven enough that the driest plants go short or the rest get too much; flush the laterals, clean filters and check for clogging and pressure differences.

What are signs of clogged emitters?

Catches well below the rest, dry spots around some plants, and an average well under the rated flow. Several emitters at half flow while neighbours are normal is classic partial clogging; a zero catch is a fully blocked emitter.

PC or non-PC emitters?

PC emitters keep their flow across a wide pressure range, so they suit long rows, slopes and mixed elevations. Non-PC emitters cost less and suit short, level runs at steady pressure.

Why use the rated flow instead of K?

Metric spec sheets often give K with pressure in metres, while others use bar or psi, and a wrong unit gives a wrong flow. Starting from a rated flow at a rated pressure avoids that, because the pressure units cancel.

Sources

  1. B.C. Ministry of Agriculture and Food, B.C. Trickle Irrigation Manual (1999), Appendix E: Equations. Emitter flow rate Q = Kd × P^x, the discharge exponent from two readings, and emission uniformity from the manufacturer’s coefficient (1 − 1.27 Cv ÷ √n).
  2. Netafim, Streamline X technical product sheet. Q = K × P^x with P in metres, K and x for each dripper, ISO 9261 requiring both to be declared, and 10 % flow variation as uniform irrigation.
  3. Netafim, UniGray CNL and HCNL technical product sheet. Pressure-compensated drippers with an exponent of 0 inside their working pressure range.
  4. Irrigation Association (Lamm & Rogers, Kansas State University), Hydraulic Considerations for SDI Systems (2012 Technical Conference). Emitter discharge variation and design emission uniformity equations, and the 10 / 20 % flow-variation bands (Bralts et al., 1987).
  5. The catch-volume conversion, low-quarter field EU and the EU rating bands are common field-evaluation practice, not a standard; exponent presets for vortex and laminar emitters are typical values, editable.

Links checked November 15, 2026. The rated-flow route was checked against a published K and x (1.60 L/h dripper, K 0.568, x 0.45, P in metres) at 10 and 15 m.