Sprinkler Distribution Uniformity Calculator

Paste the readings from a catch-cup test and see how evenly the zone waters. The calculator sorts the cups, finds the driest quarter, and gives the lower-quarter DU, the Christiansen CU, the scheduling multiplier and the Irrigation Association rating for your head type.

Distribution uniformity calculator

Quick picks

1Readings

Any unit works if every cup is the same size; DU has no unit.

Separate them with commas or spaces. At least 8, up to 64; 12–24 recommended. Enter 0 for a dry cup.

2The zone

Head type in the zone Required
See your DU ↓

How the calculator works

Distribution uniformity (DU) tells you how evenly a zone waters. A DU of 75 % means the driest quarter of the lawn gets 75 % of the average water.

You paste the cup readings. The calculator sorts them, takes the driest quarter, and compares that quarter’s average with the average of all cups. It also works out Christiansen’s coefficient (CU), which looks at every cup, and the scheduling multiplier that stretches run times to wet the dry spots.

  • Cups in the low quarternLQ = n ÷ 4, rounded to the nearest whole cup (halves up), at least 1
  • Lower-quarter DUDU = average of the lowest nLQ cups ÷ average of all cups × 100
  • Christiansen CUCU = 100 × [1 − Σ|x − mean| ÷ (n × mean)], shown as 0 if negative
  • Scheduling multiplierSM = 1 ÷ (0.4 + 0.6 × DU), with DU as a fraction

Depths in inches, millimetres or volumes in millilitres all give the same DU, because the units cancel. The cups must be the same size. Need the readings first? Run the cup test on the precipitation rate calculator; with 8 or more cups, its link fills them in here.

Worked examples

Sixteen cans on a spray zone

  1. Readings0.7, 0.8, 0.9, 0.6, 0.8, 0.7, 0.9, 0.7, 1.0, 0.8, 0.8, 0.9, 1.0, 0.8, 0.9, 1.0 in.
  2. Sorted, lowest 40.6, 0.7, 0.7, 0.7 → average 0.675 in. All 16 average 13.3 ÷ 16 = 0.831 in.
  3. DU0.675 ÷ 0.831 × 100 = 81.2 %: excellent for sprays.
  4. CU and multiplierCU = 88.3 %; SM = 1 ÷ (0.4 + 0.6 × 0.812) = 1.13.

The extension publication rounds the averages to 0.7 and 0.8 before dividing and gets 87.5 %. Rounding first adds six points; the calculator keeps full precision.

Fifteen readings in millilitres on a rotor zone

  1. Readings47, 42, 45, 24, 13, 26, 33, 34, 27, 30, 40, 44, 32, 12, 12 mL.
  2. Low quarter15 ÷ 4 = 3.75 → 4 cups: 12, 12, 13, 24 → average 15.25 mL. All 15 average 30.73 mL.
  3. ResultDU = 49.6 %, CU 69.1 %, SM 1.43. For rotors that is “repair before scheduling”.

DU ratings by head type

Irrigation Association ratings for lower-quarter DU.
RatingSpray headsRotors and rotary nozzlesScheduling multiplier
Excellent75 % and up80 % and up1.18 or less
Very good65–74 %70–79 %1.19–1.27
Good55–64 %65–69 %1.28–1.37
Fair50–54 %60–64 %1.38–1.43
Poor40–49 %50–59 %1.44–1.56
Repair before schedulingunder 40 %under 50 %over 1.56

The multiplier column is for spray heads. The IA best-practice minimum is 55 % for sprays and 70 % for rotors. Drip zones aren’t rated by this table; check emitter flow instead.

How to run the cup test

  1. Check firstFix any broken, tilted or blocked heads before you test; you want the zone’s real pattern, not one fault.
  2. Lay outPlace 12–24 identical cups in a grid, about a third of the spacing from heads and between them.
  3. RunRun the zone long enough to catch a measurable amount, usually 15–20 minutes, in calm weather.
  4. ReadRead every cup, including dry ones as 0, and paste the numbers in any order.

DU and your run time

If you water just long enough for the average spot, the driest quarter stays short. The scheduling multiplier stretches the run so the dry spots get enough, at the cost of overwatering the wet ones.

Scheduling multiplier for common DU values.
DUMultiplier20 minutes becomes
85 %1.1022 min
75 %1.1824 min
60 %1.3226 min
50 %1.4329 min
40 %1.5631 min

Enter your DU on the run time calculator and it applies the multiplier.

How to raise a low DU

  • Straighten tilted heads and raise sunken ones so they clear the grass.
  • Clean or replace clogged nozzles and screens.
  • Use matched-precipitation nozzles so quarter, half and full circles put down the same rate; the nozzle flow calculator sets the flows.
  • Check spacing is head-to-head; the sprinkler spacing calculator works it out from the throw.
  • Check pressure at the last head; too low gives a doughnut pattern, too high gives mist that drifts.

Mistakes to avoid

Rounding before dividing

Round the averages to one decimal first and DU can shift by several points. Keep full precision until the end.

Leaving out dry cups

A dry cup is the most important reading: it is a coverage gap. Enter it as 0.

Mixed cup sizes

Volumes only compare if every cup has the same opening. Use identical cups, or convert each to depth first.

Testing in wind

Wind moves water across the zone. Test in the morning calm, at normal pressure.

How we build and check this calculator

Every formula on this page names its source, and the code is tested against worked cases before every update.

  • Methods from recognised sources. Lower-quarter DU, the multiplier and the ratings follow Irrigation Association papers; the worked example comes from University of Florida IFAS Extension. See the sources.
  • Tested against worked cases. Cases run against the calculator code before every update: the 16-can extension example, a 15-reading millilitre rotor test, a 24-cup audit, an 8-cup uneven zone, and too-few-cups and all-dry errors. All must match.
  • Honest about limits. A DU describes one test on one day. Wind, pressure and season change it; retest after repairs.
  • Your entries stay on your device. The calculator runs in your browser. Readings carried over from the cup test stay in this browser tab only.
  • Corrections are welcome. If a number looks wrong, tell us. We check it against the sources, fix the page and update the date at the top.

Page history

Published. Methods, test cases and source links checked.

Questions

What is a good distribution uniformity for sprinklers?

For spray heads, 75 % or more is excellent and 55 % is the Irrigation Association’s best-practice minimum. For rotors the bar is higher, 80 % excellent and 70 % minimum. Below 40 % (sprays) or 50 % (rotors), repair the zone before you schedule it.

How many catch cups do I need for a DU test?

Use 12–24 cups for a typical residential zone. The calculator accepts as few as 8 and warns below 12, because with few cups one odd reading moves the result a lot. Large zones can use more, up to 64.

What is the difference between DU and CU?

DU compares the driest quarter with the average, so it is sensitive to dry spots, which is what browns a lawn. CU, Christiansen’s coefficient, uses the average difference of every cup from the mean. CU is usually higher than DU for the same zone.

How do I use DU to set my run time?

Multiply the plain run time by the scheduling multiplier, 1 ÷ (0.4 + 0.6 × DU). At DU 60 % that is 1.32, about a third longer. The run time calculator applies it for you if you enter the DU.

How do I improve a low DU?

Fix the heads first. Straighten tilted heads, raise sunken ones, clear blocked nozzles, match nozzles to the arc, and check pressure and spacing. Each fix saves more water than adding minutes, which overwaters the rest of the zone.

What if my number of cups doesn’t divide by 4?

The low quarter is n ÷ 4 rounded to the nearest whole cup, with halves rounded up. For 15 cups, 15 ÷ 4 = 3.75, so the lowest 4 cups are used; for 18 cups, 4.5 rounds up to 5.

Can I enter millilitres instead of depth?

Yes. Choose volume in mL. As long as every cup is the same size, the units cancel out and the DU is the same as with depths.

Sources

  1. Irrigation Association, Using Distribution Uniformity to Evaluate the Quality of a Sprinkler System (Mecham, 2004). Lower-quarter DU from catch-can data, the scheduling multiplier and how DU relates to watering more to cover dry spots.
  2. Irrigation Association, Spacing and Pattern Effects on DULQ of Spray Heads (2006). The 55 % DULQ minimum for pop-up spray heads and how spacing changes uniformity.
  3. University of Florida IFAS Extension, Field Evaluation of Container Nursery Irrigation Systems (AE194). DU as the low-quarter average divided by the overall average, the 16-can worked example, and low (under 60 %) and high (80 % and over) uniformity.
  4. LibreTexts Workforce, Irrigation Systems Management (AET 021), 11.3: Sprinkler Performance. How pressure, spacing and wind affect sprinkler distribution.
  5. Rain Bird Corporation, Technical Newsletter, Spring 2001: Sprinkler Spacing. Head-to-head spacing and matched precipitation as the basis of even coverage.
  6. The rounding of the low quarter, the Christiansen CU formula (Christiansen, 1942) and the rating thresholds as applied here are set out on this page.

Links checked November 15, 2026. The 16-can example was recomputed exactly; the published version rounds the averages to one decimal, which is why it shows a slightly different DU.

Related guides