Irrigation Wire Size Calculator
Check whether a 24 VAC sprinkler valve gets enough voltage at the end of its wire run. Enter the controller output, the solenoid’s needs and the distance, and see the voltage at the solenoid, pass or fail, the smallest wire pair that works and the longest run for each gauge, with one valve or several on a shared common.
Irrigation wire size calculator
How the calculator works
A sprinkler valve opens when its solenoid gets enough voltage. Every foot of wire uses up a little of the controller’s 24 volts, so a long or thin wire can leave too little at the valve.
- Allowable dropVa = controller output − solenoid minimum
- Wire resistanceR = ρ ÷ A, copper ρ = 1.7241 × 10⁻⁸ Ω·m · AWG diameter d = 0.005 × 92^((36 − n) ÷ 39) in
- Voltage dropdrop = L × I × (Rcontrol + N × Rcommon), L one way, R per unit length
- At the solenoidV = controller output − drop; pass if it is at least the minimum
- Longest runLmax = Va ÷ [I × (Rcontrol + N × Rcommon)]
N is the number of valves on at the same time sharing the common. Inrush current is used because it is the highest the solenoid draws.
Worked examples
500 ft on 18 AWG
- Inputs26 V controller, 21 V minimum, 0.30 A inrush, 500 ft, 18 AWG control and common.
- Drop500 × 0.30 × (6.385 + 6.385) ÷ 1,000 = 1.92 V.
- Result26 − 1.92 = 24.08 V: passes.
1,200 ft on 18 AWG
- Inputs24 V, 20 V minimum, 0.37 A, 1,200 ft, 18/18.
- Drop1,200 × 0.37 × 12.77 ÷ 1,000 = 5.67 V → 18.33 V: fails.
- Fix16 AWG for both: 1,200 × 0.37 × 8.03 ÷ 1,000 = 3.57 V → 20.43 V: passes.
Two valves on a shared common
- Inputs24 V, 20 V minimum, 0.37 A, 600 ft, 18 AWG control, 16 AWG common, 2 valves on.
- Drop600 × 0.37 × (6.385 + 2 × 4.015) ÷ 1,000 = 3.20 V.
- Result20.80 V: passes, with a longest run of 750 ft. With an 18 AWG common, only 564 ft.
Maximum distance by wire size
| Control / common | One valve | Two valves on the common |
|---|---|---|
| 18 / 18 AWG | 847 ft | 564 ft |
| 18 / 16 AWG | 1,039 ft | 750 ft |
| 16 / 16 AWG | 1,346 ft | 897 ft |
| 16 / 14 AWG | 1,653 ft | 1,192 ft |
| 14 / 14 AWG | 2,140 ft | 1,427 ft |
| 12 / 12 AWG | 3,403 ft | 2,269 ft |
| 10 / 10 AWG | 5,412 ft | 3,608 ft |
| 1.0 / 1.0 mm² | 314 m | 209 m |
| 1.5 / 1.5 mm² | 470 m | 314 m |
| 2.5 / 2.5 mm² | 784 m | 523 m |
For your own voltages and current, the calculator draws the same comparison for every same-size pair under the result.
Wire resistance
| Size | Ohms per 1,000 ft | Ohms per km |
|---|---|---|
| 18 AWG | 6.385 | 20.95 |
| 16 AWG | 4.015 | 13.17 |
| 14 AWG | 2.525 | 8.29 |
| 12 AWG | 1.588 | 5.21 |
| 10 AWG | 0.999 | 3.28 |
| 8 AWG | 0.628 | 2.06 |
Each step down in AWG number cuts resistance by about 37 %. Warm wire in summer soil has a little more resistance; the margin between your solenoid minimum and its real limit covers that.
Several valves on one common
Each valve has its own control wire, but they usually share one common back to the controller. When a master valve and a zone valve are on together, or two zones run at once, the common carries both currents. The shared-common tab multiplies the common’s drop by the number of valves on. Upsizing the common is the cheapest way to restore distance.
Most controllers run one zone and the master valve at a time. Check the controller’s station output limit before running more. For flow per zone, see the sprinkler zone calculator.
Mistakes to avoid
Counting one way only
The current goes out and back. Enter the one-way distance; the calculator doubles the path.
Using holding current
The solenoid draws about twice as much while opening. Size for inrush.
A thin common
The common carries every valve’s current. Keep it the same size as the control wire or one size larger.
Wiring the mains yourself
24 VAC is low voltage, but the controller’s 120/230 V supply side must be wired to local electrical code by a qualified person.
How we build and check this calculator
Every formula on this page names its source, and the code is tested against worked cases before every update.
- Methods from recognised sources. The allowable-drop method follows Nelson Irrigation and Rain Bird notes; resistance comes from the copper standard and the AWG rule; the results are checked against Hunter’s distance table. See the sources.
- Tested against worked cases. Twelve cases run against the calculator code before every update: six maximum distances from the manufacturer table, a passing and a failing run, two shared-common runs, a metric run and an impossible voltage setting. All must match.
- Honest about limits. Splices, corroded connections and low mains voltage all eat into the margin. Measure at the valve if a zone won’t open.
- Your entries stay on your device. The calculator runs in your browser. Nothing you type is sent anywhere; your inputs live only in the page address, so you can bookmark or share a result.
- Corrections are welcome. If a number looks wrong, tell us. We check it against the sources, fix the page and update the date at the top.
Page history
- Published. Methods, test cases and source links checked.
Questions
What size wire do I need for sprinkler valves?
18 AWG multi-strand irrigation cable works for most home runs up to about 800 ft with a typical solenoid. For longer runs, upsize the common first, then the control wire. The calculator finds the smallest size for your distance.
How far can I run 18 gauge sprinkler wire?
About 850 ft one way with 24 V at the controller, a 20 V solenoid minimum and 0.37 A inrush. Run two valves on the same common and it drops to about 560 ft.
Why does the common wire matter more?
Every valve that is on sends its current back through the common. With two valves running, the common carries twice the current and drops twice the voltage. A bigger common lets a run go farther.
What is inrush current?
The surge a solenoid draws in the first moment, while it pulls the plunger open. It is about twice the holding current, so it sets the worst-case drop. Find it on the solenoid’s spec sheet.
Why do I count the distance twice?
Current goes out on the control wire and comes back on the common. The wire the current travels is twice the one-way distance; the calculator does this for you.
My valve hums or chatters. Is it the wire?
Often. Too little voltage at the solenoid lets it pull in weakly, so it buzzes or won’t open. Measure the voltage at the valve with the zone on; if it is below the solenoid minimum, the wire is too small or too long.
Does this work for decoder systems?
No. Two-wire decoder systems and battery DC-latching valves work differently; follow the maker’s wiring tables for those.
Sources
- Hunter Industries, Valves: maximum wire distance between controller and valves. Maximum one-way distances by control and common gauge (18/18 850 ft, 16/16 1,340, 14/14 2,150, 12/12 3,390, 10/10 5,400, 16/14 1,650; 1.0 mm² 290 m) at 350 mA inrush, and halving the distance for two solenoids.
- Hunter Industries, Valve solenoid specification. 24 VAC solenoid with 350 mA inrush and 190 mA holding at 60 Hz, and a 19 VAC minimum.
- Nelson Irrigation, Control Wire Size Notes (VM-20.11). Allowable voltage loss as controller output minus solenoid minimum, and the out-and-back return through the common.
- Rain Bird Corporation, SPECNEWS on control wire sizing. Sizing the worst-case pair, with control and common equal or one size apart.
- Wire resistance from the copper resistivity standard (1.7241 × 10⁻⁸ Ω·m at 20 °C) and the AWG diameter rule, the drop and maximum-distance formulas and the metric table are derived on this page.
Links checked November 15, 2026. The computed distances were checked against the Hunter table; they match within 1 % except the metric 1.0 mm² figure, where Hunter allows for stranded cable (290 m against 314 m for solid copper).