Irrigation Pump Calculator

Add up the total dynamic head your irrigation pump must produce — lift or pumping water level, elevation, friction and the pressure the heads need, less any inlet pressure — then see the water horsepower, brake horsepower, electric motor size to buy, or the engine horsepower for a diesel or gas drive.

Irrigation pump calculator

Choose your water source
Quick picks

1Source

ft
psi

2Flow and heads

GPM

The flow the pump must deliver at the heads.

ft
Friction loss entered as Required
ft

Calculate it; psi × 2.31 = feet.

psi
psi

3Pump

%

Good centrifugal and turbine pumps reach 75–82 %; field average is often lower.

Drive Required
See the pump size ↓

How the calculator works

A pump has to lift water, push it through pipe and deliver it at the pressure the sprinklers need. Total dynamic head (TDH) puts all of that in feet; horsepower follows from TDH and flow.

  • Pressure headft = psi × 2.31
  • Surface or boosterTDH = suction lift + elevation + friction + pressure head − inlet pressure × 2.31
  • WellTDH = pumping water level + elevation + friction + pressure head
  • Water horsepowerWHP = GPM × TDH ÷ 3,960 · metric kW = 9.81 × Q (m³/s) × H (m)
  • Brake horsepowerBHP = WHP ÷ pump efficiency
  • Electric motornameplate ≈ BHP ÷ 0.9, then the next standard size
  • EngineBHP ÷ (0.80 × 0.95 × 0.91 × 0.96): continuous duty, right-angle drive, 3,000 ft, 100 °F

Find the friction with the friction loss calculator; enter it in feet or psi.

Worked examples

A pond pump for sprays

  1. TDH6 ft lift + 5 ft elevation + 20 ft friction + 30 psi × 2.31 = 100.3 ft at 50 GPM.
  2. PowerWHP 50 × 100.3 ÷ 3,960 = 1.27 hp; BHP at 70 % = 1.81 hp; nameplate 2.01 hp → 3 hp motor.

A booster on city water

  1. TDH10 ft elevation + 4.6 psi friction (10.6 ft) + 50 psi needed − 30 psi supplied (46.2 ft) = 66.8 ft at 15 GPM.
  2. PowerWHP 0.25 hp; BHP at 60 % = 0.42 hp → 0.5 hp.

An irrigation well

  1. TDH150 ft pumping level + 10 ft + 15 psi friction (34.65 ft) + 60 psi (138.6 ft) = 333.3 ft at 300 GPM.
  2. PowerWHP 25.25 hp; BHP at 75 % = 33.66 hp → 40 hp motor, or an engine of about 50.7 hp.

Metric

  1. Inputs10 L/s against 40 m at 70 % efficiency.
  2. Result9.81 × 0.010 × 40 ÷ 0.70 = 5.61 kW (7.52 hp) at the shaft.

What makes up TDH

The parts of total dynamic head.
PartWhat it isWhere to get it
Suction liftWater surface below the pump (− if above)Measure; keep under about 15 ft
Pumping water levelDepth to water in a well while pumpingWell test or driller’s log
ElevationPump to the highest outletSite levels or a map
FrictionPipe and fittings at the design flowFriction loss calculator
Pressure headPressure the heads need × 2.31Nozzle chart

Horsepower and motor size

Water horsepower is the useful work. Brake horsepower adds the pump’s own losses; a motor is then chosen a little above BHP. Standard motor sizes run 0.5, 0.75, 1, 1.5, 2, 3, 5, 7.5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 125, 150 and 200 hp. Engines lose output to continuous running, the gear head, altitude and heat, so they need more rated horsepower than the shaft uses. Lower efficiency means higher running cost every hour the pump runs.

Booster pumps on city water

A booster only has to make up the difference between what the supply gives at your flow and what the heads need. Enter the city pressure as the inlet pressure. If the result says no booster is needed, the shortfall lies elsewhere; check the pressure budget first. Local rules often require approved backflow protection with a booster.

Well pumps and drawdown

A well’s water level falls while it pumps. Use the pumping level, static depth plus drawdown, as the lift. The well must also yield the flow you ask of it; the pump can’t make more water than the well gives.

Mistakes to avoid

Using static water level

For wells, use the pumping level. Static level understates the lift.

High suction lift

Above about 15 ft, centrifugal pumps risk cavitation. Check the pump’s NPSH.

Picking by horsepower alone

Two pumps with the same motor can deliver very different flow and head. Use the pump curve.

Forgetting the pressure head

30 psi at the heads is 69 ft of head, often the biggest part of TDH.

How we build and check this calculator

Every formula on this page names its source, and the code is tested against worked cases before every update.

  • Methods from recognised sources. TDH, horsepower and derating follow K-State Extension’s formula sheet; efficiencies and the check example follow Texas A&M Extension. See the sources.
  • Tested against worked cases. Six cases run against the calculator code before every update: a pond pump, a booster, an irrigation well with an engine, the Texas A&M example, a metric pump and a supply that needs no pump. All must match.
  • Honest about limits. This sizes the duty, not the pump. Large pumping plants need a professional design.
  • Your entries stay on your device. The calculator runs in your browser. Nothing you type is sent anywhere; your inputs live only in the page address, so you can bookmark or share a result.
  • Corrections are welcome. If a number looks wrong, tell us. We check it against the sources, fix the page and update the date at the top.

Page history

Published. Methods, test cases and source links checked.

Questions

What is total dynamic head?

It is the total height, in feet, the pump has to lift the water, from the water surface to the pump, up to the highest outlet, plus the friction in the pipe, plus the pressure the heads need expressed as feet (psi × 2.31).

How do I size an irrigation pump?

Work out the flow you need and the total dynamic head at that flow, then pick a pump whose curve passes through that point near its best efficiency. Horsepower tells you the motor size, but the curve picks the pump.

What is the difference between water and brake horsepower?

Water horsepower is the power that ends up in the water (GPM × TDH ÷ 3,960). Brake horsepower is what the pump shaft needs, larger because no pump is perfect. It equals water horsepower ÷ pump efficiency.

Do I need a booster pump on city water?

Only if the pressure at the heads falls short. Enter your city pressure as the inlet pressure; if it already meets the need at your flow, no booster is required. The pressure calculator shows what reaches the heads.

What is pumping water level?

The depth to water in a well while the pump runs, the static depth plus drawdown. It, not the static level, is the lift a well pump works against.

How does efficiency affect running cost?

Every point of efficiency lost is paid for in energy, every hour. Good centrifugal and turbine pumps reach 75–82 %, but many field pumps run well below that. A pump test shows where yours is.

Sources

  1. Kansas State University Research and Extension, Irrigation Formulas and Conversions (MF-2404). TDH components, water horsepower = GPM × TDH ÷ 3,960, brake horsepower = WHP ÷ efficiency, electric nameplate and engine derating factors.
  2. Texas A&M AgriLife Extension (Fipps), Calculating Horsepower Requirements and Sizing Irrigation Supply Pipelines (EB-6011). Water horsepower, total dynamic head, 1 psi = 2.31 ft, pumping plant efficiencies, and a worked example used as a check (750 GPM at 535.5 ft, about 135 BHP).
  3. B.C. Ministry of Agriculture and Food, B.C. Trickle Irrigation Manual (1999), Appendix E — Equations. Pump horsepower from flow, total head and efficiency (HP = Q × H ÷ 3,960E).
  4. The motor size list is the standard NEMA horsepower series; the metric power formula (kW = 9.81 × Q × H ÷ E) and unit conversions are derived on this page.

Links checked November 15, 2026. A course page that ranks for this topic lists water horsepower 1.7 for 50 GPM at 100.3 ft; the published formula gives 1.27, which is what this page uses.