Furrow Irrigation Calculator
For furrow (row) irrigation, find the stream size per furrow and the gross and net depth a set applies — or the set time for a target depth. Works with siphon tubes (chart flow or an estimate from size and head), gated pipe in gpm or cfs, or a known flow per furrow, with every-other-furrow, a cutoff-ratio check against soil and tailwater targets, and an erosion check from slope.
Furrow irrigation calculator
How the calculator works
Each furrow gets a stream of water for the length of the set. How deep it soaks in depends on the stream, the time, the furrow length and the spacing.
- Stream sizegated: total ÷ gates · known: as entered · siphons: tubes × gpm per tube
- Siphon estimateQ (cfs) = C × A × √(2gH), A in ft², H in ft; gpm = cfs × 448.83
- Gross depthin = 1,155 × gpm × hours ÷ (length ft × wetted spacing in); net = gross × efficiency
- Set timehours = depth × length × wetted spacing ÷ (1,155 × gpm)
- Every other furrowwetted spacing = 2 × furrow spacing
- Cutoff ratioadvance time ÷ set time; target advance = target ratio × set time
- Erosion checklargest non-erosive stream ≈ 12.5 ÷ slope % (gpm)
Worked examples
A 12-hour set
- Inputs750 gpm on 100 furrows (7.5 gpm); 12 h; 1,320 ft; 30 in.
- Result2.63 in gross. For 3 in, run 13.71 h.
Gated pipe with a cutoff check
- Inputs760 gpm; 80 gates; 24 h; 2,600 ft; 30 in; water reaches the end in 15 h; sandy soil, no reuse.
- Result9.50 gpm a furrow; 3.38 in; cutoff ratio 0.63 against a 0.50 target — too high. Aim for a 12.0-hour advance with a bigger stream.
- Revised set48 gates → 15.83 gpm; 2.81 in in 12 h; at 0.8 % slope that is just over the 15.6 gpm erosion limit.
A ditch delivery in cfs
- Inputs6 cfs (2,693 gpm); 96 rows at 40 in; 800 ft; 6.5 h.
- Result28.05 gpm a row; 6.58 in on 5.88 acres. With 5 cfs on 45 rows, 1,100 ft, 4 in takes 3.06 h.
Efficiency, every other furrow, metric
- Efficiency10 gpm; 11 h; 660 ft; 36 in; 50 %: 5.35 in gross, 2.67 in net.
- Every other furrow9.5 gpm; 12 h; 1,320 ft; 30 in spacing (60 in wetted): 1.66 in.
- Metric1 L/s a furrow; 8 h; 400 m; 750 mm spacing: 96.0 mm.
Cutoff ratio targets
| Tailwater | Sandy | Loamy | Clayey |
|---|---|---|---|
| No reuse | 0.50 | 0.70 | 0.90 |
| With reuse | 0.20 | 0.40 | 0.50 |
| Blocked ends | 0.70 | 0.85 | 0.95 |
Above the target, water reaches the end too late and the top end gets too much; increase the stream (fewer gates) or shorten runs. Well below it, more runs off; reduce the stream or set time. The depth to aim for is what the root zone can hold; see the available water capacity calculator, and plan the next set with the irrigation schedule calculator.
Siphon tube flow
Head is the height of the ditch water surface above the centre of a free outlet, or the difference between the two water surfaces when the outlet is submerged. With C = 0.64, a 2-in tube at 6½ in of head gives 37.0 gpm (an ideal orifice would give 57.8), and a 1.5-in tube at 4 in about 16.3 gpm. Real tubes vary with length and material, so use your tube chart whenever you have it.
Stream size and erosion
| Slope | Stream |
|---|---|
| 0.25 % | 50.0 gpm |
| 0.5 % | 25.0 gpm |
| 0.8 % | 15.6 gpm |
| 1.0 % | 12.5 gpm |
| 1.25 % | 10.0 gpm |
Need the flow for the whole field? See the system capacity calculator. To measure a ditch delivery, use the weir and flume flow calculator.
Mistakes to avoid
Row spacing on every-other-furrow
When you water alternate furrows, the wetted spacing doubles. The toggle does it for you.
Trusting depth alone
The average depth can be right while the top end is soaked and the bottom dry. Check the cutoff ratio.
Long first irrigations
The first set after cultivation advances slowly and soaks in more. Expect a deeper application.
Guessing siphon flow
A small change in head or tube size changes flow a lot. Measure the head.
How we build and check this calculator
Every formula on this page names its source, and the code is tested against worked cases before every update.
- Methods from recognised sources. The depth equation, cutoff targets and erosion rule follow University of Nebraska Extension; efficiencies follow NCAT ATTRA. See the sources.
- Tested against worked cases. Eleven cases run against the calculator code before every update, including the Nebraska, NCAT and Arizona examples, every-other-furrow, two siphon estimates and a metric set. All must match.
- Honest about limits. Surge irrigation and infiltration modelling are beyond this page.
- Your entries stay on your device. The calculator runs in your browser. Nothing you type is sent anywhere; your inputs live only in the page address, so you can bookmark or share a result.
- Corrections are welcome. If a number looks wrong, tell us. We check it against the sources, fix the page and update the date at the top.
Page history
- Published. Methods, test cases and source links checked.
Questions
How much water does a furrow set apply?
Gross inches = 1,155 × stream size (gpm) × set hours ÷ (furrow length in feet × wetted spacing in inches). 7.5 gpm for 12 hours on 1,320 ft furrows at 30 in puts on about 2.6 in.
How long should I run a set?
Set time = target depth × length × wetted spacing ÷ (1,155 × stream size). For 3 in with the same furrows and stream, about 13.7 hours. Then check the cutoff ratio so water reaches the end at the right time.
What is a cutoff ratio?
Average time for water to reach the end of the furrow, divided by the set time. University of Nebraska targets range from 0.2 (sandy, with reuse) to 0.95 (clayey, blocked ends). Too high means the top of the field is over-watered.
How many gates should I open?
Enough to give each furrow the stream size you want. Fewer gates means bigger streams that reach the end sooner; too big a stream erodes. The erosion check and cutoff ratio help you choose.
How much water does a siphon tube deliver?
It depends on its inside diameter and the head (the height of the ditch water above the outlet, or surface to surface if submerged). A 2-in tube at 6½ in of head runs about 37 gpm. Use your tube chart if you have one.
What is every-other-furrow irrigation?
Watering alternate furrows, which doubles the wetted spacing. Guides report about 20–30 % less water applied with similar yields where watered furrows are no more than 6 ft apart.
How big a stream can a furrow take without eroding?
A rule of thumb from University of Nebraska is about 12.5 ÷ slope % gpm. At 0.8 % slope that is about 15.6 gpm.
Sources
- University of Nebraska–Lincoln Extension, Managing Furrow Irrigation Systems (G1338). Stream size, the 1,155 gross-depth equation, cutoff ratio targets (Table I), every-other-furrow and the non-erosive stream rule; worked examples used as checks.
- University of Nebraska–Lincoln Extension, Management Recommendations for Blocked-end Furrow Irrigation (G1721). Cutoff-ratio management for blocked-end systems.
- University of Nebraska–Lincoln CropWatch, Using Cutoff Ratio to Fine-Tune Furrow Irrigations. Target cutoff ratios by system and soil, and why reuse systems run lower ratios.
- NCAT ATTRA, Measuring and Conserving Irrigation Water. Net application with efficiency, furrow efficiencies of 60–80 %, and a furrow example (2.7 in net) used as a check.
- The 1,155 constant (60 × 231 ÷ 12) is exact. The siphon estimate uses the orifice form Q = C·A·√(2gH) as in University of Idaho’s siphon bulletin; the default C = 0.64 is calibrated to one chart point in a Texas A&M AgriLife siphon tube bulletin (2-in tube, 6½-in head, 37 gpm). The cfs conversion (448.83 gpm) and metric version are derived on this page.
Links checked November 16, 2026. The page reproduces the Nebraska examples (2.6 in; 9.5 gpm, 3.4 in, ratio 0.63) and University of Arizona’s Irrigator’s Equation examples (6 cfs → 6.6 in; 5 cfs → about 3 h). Nebraska rounds 760 ÷ 48 to 15.6 gpm and calls it within the erosion limit; the exact 15.83 gpm is just over, so the page flags it.